CDA Cooktop HCC762 User Manual

HCC762 Ceramic Hob  
Manual for Installation, Use and Maintenance  
Customer Care Department • The  
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY  
T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu  
 
Please note:  
Before operating this hob, please read the instructions carefully  
After unpacking the appliance, make sure it is not damaged. In case of doubt, do not use the appliance and contact your  
supplier.  
Remove all packaging and do not leave the packing materials in easy reach of children as they may cause serious injury. The  
packaging materials are recyclable.  
Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance.  
Ceramic hobs become hot and remain hot during and immediately after use. Do not touch the hob until it has been allowed  
to cool.  
After use, please ensure that all the zones have been switched off.  
Keep children away from the appliance when in use.  
Pan handles should never stand out beyond the edge of the worktop. This will ensure children cannot reach them.  
Do not use pans with rough bases (e.g. cast iron) as these may scratch the hob surface.  
Ensure the base of the saucepan is clean and dry before placing it on the zone.  
Do not switch on the zones without cookware in place.  
Do not lean over the hob when it is in use.  
Do not drop heavy or sharp objects on to the hob top.  
Do not scratch the hob top with sharp objects.  
Follow the cleaning instructions carefully.  
Never put cooking foil or plastic materials on the hob top when it is hot. These materials could melt and cause damage to  
the hob.  
Do not leave inflammable materials on the hob top.  
Never use the hob top for storage or as a worktop.  
Do not leave wet or damp pan lids on the hob.  
Important  
Do not use the hob if the glass surface is cracked or damaged to prevent risk of electric shock, Disconnect it from the power  
supply.  
Do not use the hob if the electrical cord is damaged.  
When correctly installed, this hob meets all the safety requirements laid down for this type of product. However, special  
care should be taken around the underneath of the appliance as this area is not designed or intended to be touched and may  
contain sharp or rough edges, that may cause injury.  
This hob (Class 3) has been designed for use only as a cooking appliance. Any other use (e.g. heating rooms) should be  
considered incorrect and therefore dangerous.  
This appliance is not intended to be operated by any means of an external timer or separate remote control system.  
Make sure that electrical cords connecting other appliance do not come into contact with the hob top.  
Before disposing of an unwanted appliance, it is recommended that it is made inoperative and that all potentially hazardous  
parts are removed.  
2
 
Using your hob  
Zones:  
1.  
Front left 0.7/2.1 kW 120/210 mm dual  
2
3
2. Rear left 1.2 kW 140 mm  
3. Rear right 1.1/2 kW 145 x 270 mm dual  
4. Front right 1.2 kW 140 mm  
5. Touch control panel  
1
4
5
Fig.1  
The Touch Control  
8
9
10 11 12  
1
2
3
4
5
6
7
8
9
Dual zone key  
Minus key (for all zones)  
Timer key  
Plus key (for all zones)  
Zone selection key  
Childlock key  
Power key  
Timer display  
Timer zone indicator  
10 Zone display  
11 Dual zone indicator  
12 Childlock indicator  
1
2
3
4
5
6
7
Fig.2  
3
 
How to use the hob  
The ceramic surface of the hob allows fast transmission of heat vertically from the heating elements under the glass to  
the pans on the hob top.  
The heat does not spread horizontally, so the hob top remains relatively cool only a few centimetres from the zone in  
use.  
To switch the hob on  
Touch and hold until the zone displays show 0 or H and the zone indicators flash.  
Please note:  
If a zone is not selected within 10 seconds, the hob will automatically switch off.  
To switch on a zone  
Once the hob is switched on, touch for the zone required. The zone indicator will switch on to confirm the zone is  
active.  
Touch and hold to select the power level from 1 (minimum) to 9 (maximum). The power level selected will show on  
the zone display.  
If required, touch again to deactivate the touch control for the zone.  
To adjust the power level once set  
Touch for the zone required. The zone indicator will switch on to confirm the zone is active.  
Touch and hold or until the required power level shows on the zone display.  
To use the dual zone  
The dual zones are formed of two separate coils of resistant material.  
Once the zone is switched on, touch at any time to switch the dual zone on or off. The dual zone indicator will  
switch on when the dual zone is on.  
To switch off a zone  
Touch for the zone required.  
EITHER Touch and at the same time.  
OR Touch until the zone display shows 0.  
The zone display will show 0 for approximately eight seconds before showing H to indicate the residual heat.  
To switch the hob off  
Touch and hold at any time.  
.
4
 
How to use the hob  
Power Level  
Type of cooking  
0
Switched off  
1/2  
2/3  
3/4  
4/5  
6/7  
7/8  
9
For melting (butter/chocolate) or keeping food warm  
Keeping food hot or to heat small quantites of liquid  
Heating large quantities of liguid (sauces etc.)  
Slow boiling e.g. spaghetti, soups, stews, potatoes  
Gentle frying  
Browning meats, frying fish. omelettes  
Fast frying steaks  
Booster  
The hob is equipped with a booster function, which allows a zone to run at maximum power for a preset period of time  
before returning to the required power level. These times are shown in the table. To set the booster, follow the steps  
below.  
Once the hob is switched on, touch for the zone required. The zone indicator will switch on to confirm the zone is  
active.  
Touch so the zone display shows 9.  
Touch again to set the required power level. The zone display will alternate between the required power level and A  
until the booster is complete, then it will show the required power level.  
Cooking zone  
power level  
1
2
3
4
5
6
7
8
9
Fast heating  
time  
1 min. 2 min. 4 min. 5 min.  
22 sec. 44 sec. 6 sec. 28 sec. 50 sec. 22 sec. 44 sec. 44 sec.  
6 min.  
1 min.  
2 min.  
2 min.  
n/a  
5
 
How to use the hob  
The Timer/ Minute Minder  
The timer allows you to preset the length of time any of the zones will be on, between a minimum of one minute and  
a maximum of 99 minutes. The timer can be used on each zone separately and can also be used as a minute minder, to  
countdown the time without using any of the zones.  
To set the minute minder  
Switch on the hob  
Touch . The timer display will show 00 and a dot will show on the timer display.  
EITHER Touch and hold until the required time shows on the display to set the time from zero.  
OR To go straight to 99 minutes, touch  
.
Then touch either or to adjust the time further. After approximately ten seconds, the hob will beep to confirm.  
The timer will start as soon as the time has been set.  
At the end of the set time:  
The timer display will show 00.  
The hob will beep for approximately 2 minutes. To switch off the beep and turn off the timer display, touch any key.  
To set the timer  
Switch on the hob, select the zone and set the power level.  
Touch . The timer display will show 00 and a dot will show on the timer display. The timer zone indicator will flash  
to show which zone timer is being set. If more than one zone is in use, touch repeatedly until the required timer  
zone indicator flashes.  
EITHER Touch and hold until the required time shows on the display to set the time from zero.  
OR To go straight to 99 minutes, touch  
.
Then touch either or to adjust the time further.  
Please note:  
The timer will start as soon as the time has been set.  
If more than one zone timer is set, the timer display will show the countdown with the least time to run.  
At the end of the set time:  
The zone will switch off  
The timer display will show 00, then will switch off if no other timers have been set  
The zone display will show H to indicate the residual heat.  
The hob will beep for approximately 2 minutes. To switch off the beep, touch any key.  
If no other zones are in use, the hob will switch off automatically.  
To change the timer once set  
Touch for the required zone.  
Touch either or to adjust the time.  
To cancel the timer once set  
Touch for the required zone.  
EITHER Touch and together to cancel the timer.  
OR Touch until the timer display shows 00.  
Please note:  
If you cancel the timer, the zone will continue at the set power level until it is switched off as described above.  
6
 
Safety Features  
The childlock  
The hob is equipped with a childlock to lock all the controls except , for safety reasons. This can be used when the hob is  
switched off or during cooking.  
To switch the childlock on and off  
Touch to switch the hob on.  
Touch for approximately two seconds. The childlock indicator is illuminated when the childlock is set and the hob is on.  
Residual Heat Indicators  
The hob is equipped with residual heat indicators to warn when any of the zones are still hot to the touch after cooking.  
An H will show in the relevant zone display after cooking until the zone is at a safe temperature to touch.  
Please note:  
You should avoid touching the zones when the hob is in use, or when an H is showing on the zone display.  
In the event of a power cut, the residual heat indicators will flash after the power supply is restored. However, when there is no  
power supply to the hob the residual heat indicators will not work, so extra care must be taken.  
Touch Control Safety  
The hob will not operate if an object is left on the touch control for more than ten seconds. The hob will switch off, the zone  
display will flash F and the hob will beep every 30 seconds until the object is removed.  
If the object is left on the childlock key, the childlock will switch on automatically and will need to be switched off before the  
hob can be used.  
Auto-stop Protection  
The hob is equipped with a sensor that will switch off the zone after a factory set period of time if not keys are touched once  
the zone is switched on.  
Cooking zone  
power level  
1
2
5
3
5
4
4
5
3
6
2
7
2
8
2
9
1
Time Limit  
(hours)  
10  
7
 
Efficient Use of your Hob  
The hob is equipped with zones of different sizes, designed to accommodate most shapes and sizes of pan. For best  
results, only use pans with flat bottoms and choose an appropriate zone depending on the size of the pan. The most  
efficient use of the hob is shown below, where the pan and zone are correctly chosen.  
Use pan lids where possible to minimize the energy usage of your appliance.  
As the zone will remain hot for a period of time after it has been switched off, five to ten minutes before the planned  
end of cooking time, turn the zone off. The residual heat in the hob will be sufficient to finish the cooking.  
Fig.3  
Zone Size  
120 mm  
Minimum Pan Size (mm)  
Maximum Pan Size (mm)  
100  
120  
180  
120  
150  
140 mm  
160  
239  
210 mm  
145 x 270 mm  
160 (290 with dual zone in use)  
It is very important that the pans used on the hob are made of a suitable material and have the correct type of base.  
The base should be flat and smooth, as any rough part on the pan base could scratch the ceramic hob top.  
Choose pans which are between the sizes recommended in the table above, and with bases that are as non-reflective as  
possible, e.g. dull and dark.  
Only pans recommended for use on ceramic hobs should be used.  
Pans with aluminium bases may leave silver streaks or spots on the hob. Glassware and pans with rough circulare  
machined bases should not be used  
8
 
Care and Maintenance  
Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance.  
You should use a non-abrasive cleaner to clean the hob top. Any abrasive cleaner (including Cif) will scratch the surface and  
could erase the control panel markings.  
Do not use steel wool, abrasive sponges or sharp utensils such as knives to clean the hob as these could damage the hob.  
The hob surface and the pans must be clean.  
Carefully remove any food remains (especially those containing sugar), dirt etc. as soon as is possible after spillage - using a  
ceramic hob scraper if necessary whilst the zone is still hot.  
Once they have cooled and hardened they become increasingly difficult to remove.  
Sugar, syrup and starch mixtures could permanently pit the hob surface if left to burn on and should be removed as quickly  
as possible after spillage.  
The stainless steel trims should be rinsed with water and dried with a soft, clean cloth, a chamois leather or an E-Cloth.  
All cleaner residues should be removed with a damp cloth.  
Types of residues  
Clean with  
Cleaning advice  
Wipe over the zone to be cleaned with a sponge and hot  
water, and then wipe off with a soft dry cloth.  
Light  
Cleaning sponge and soft cloth  
Accumulated baked-on stains/  
dirt, sugar spills or melted  
plastics  
Wipe over the zone to be cleaned with a sponge and hot  
water, using a ceramic scraper to remove any large marks  
or stains and then wipe off with a soft dry cloth.  
Cleaning sponge or glass scraper  
and soft cloth  
Pour a small amount of warm white vinegar onto the  
stain, leave it to stand, and then wipe off with a soft dry  
cloth.  
Rings and hard water residues  
White vinegar and soft cloth  
Important:  
Steam cleaners must not be used when cleaning this appliance.  
Mains electrical voltage:  
230 – 240Vac  
6.5 kW  
Total rated electrical consumption:  
If your Hob is not working:  
1. Check that the required zone is switched on.  
2. Check that the mains supply has not been switched off.  
3. Check that the fuse in the spur has not blown.  
Contact CDA Customer Care  
A : Customer Care Department, The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY  
9
 
Mains Electricity Connection  
Warning! this appliance must be earthed  
We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will  
comply with the I.E.E. and local regulations.  
This appliance is intended to be connected to fixed wiring and is not suitable for connection to a 13A plug or  
13A supply.  
This appliance is intended to be connected to fixed wiring by a double pole switch, having a contact separation of at least  
3mm in all poles. The switch must be positioned no further than 2m from the appliance.  
Please note:  
The mains cable must only be replaced by a qualified electrician or service engineer and must be of equivalent or  
better rating (i.e. 2.5mm2, HO5RR-F).  
This appliance is intended to be connected to the mains supply with a cable of cross section area 2.5 mm². A larger  
cable will not fit the terminal connections.  
The marking of the current rating of the fuse or circuit breaker protecting this appliance should be marked on the  
socket outlet.  
Assembly and electrical connection should be carried out by specialised personnel.  
When installing this product we recommend you seek the help of another individual.  
Ensure that the brass links are securely fitted. Failure to do so will prevent the hob from operating correctly.  
230V or 240V  
Fig.4  
10  
 
Fitting the Hob  
Unpacking the hob:  
Take care not to lose or mishandle any parts.  
Fitting position of the hob:  
This appliance must be installed a minimum of 50mm from any back wall and a minimum of 190mm away from any  
adjacent vertical surfaces, e.g. a tall cupboard end panel. This may be reduced to 100mm if the adjacent surface is resistant  
to fire (tiles or steel, for example). These dimensions are shown in Fig.5.  
If fitting a cooker hood above the hob:  
If a cooker hood is to be installed above the hob, the height of the hood above the hob must be at least 600mm (650mm is  
recommended) (Fig.6). If the instructions supplied with the hood dictate that the hood must be installed at a height greater  
than 600mm, then that height is the minimum required.  
Wall furniture requirements:  
The minimum height of any cabinet immediately above the hob is 900mm. The minimum height of any adjacent units  
(including light pelmets) is 400mm, unless they are manufactured from a material resistant to fire (steel, for example)  
Notes:  
Do not position this appliance above a refrigeration unit. The heat generated may cause the refrigeration unit to fail.  
This appliance is designed to be installed into cabinet units capable of withstanding temperatures of 65°C or greater above  
ambient temperature.  
If there is no oven to be built in below the hob, an isolation shelf should be fitted to protect the user from high  
temperatures. If the hob is to be installed above a working drawer, then a partition should be fitted to protect the contents  
and user from the heat generated during use.  
Never place perishable foods in the cupboard below the appliance.  
11  
 
How to Install the Hob  
How to install the hob:  
Overall dimensions of the hob: Width: 770mm Depth: 510mm  
Worktop cut-out dimensions:  
Width: 740mm Depth: 480mm  
1. Make the required hole in the worktop. Before doing this, you must check the instructions supplied with any cooker hood  
to ensure that you will have the required clearance. The cut-out (Fig5) shows a 60mm gap from the wall to the cut-out  
edge. The distance from the hob, when fitted, to the back wall is 50mm. If a splashback/worktop upstand is to be fitted,  
take this into account when cutting the hole. The minimum distance that the hob should be positioned away from the rear  
wall or splashback is 50mm.  
2. Position the hob seal, as shown in (Fig.7), ensuring that the ends meet without overlapping. Do not use silicone type sealant.  
3. Secure the hob to the worktop using the fixing brackets and screws supplied, as shown in (Fig.8). Remove any excess  
sealant after tightening the brackets. Do not over-tighten the fixing brackets.  
60mm  
480mm  
740mm
150mm  
1
190mm  
150mm  
190mm  
Fig.5  
Fig.6  
3cm  
4cm  
Fig.7  
Fig.8  
12  
 
13  
 
14  
 
To contact our Customer Care Department, or for Service,  
please contact us on the details below.  
Customer Care Department • The  
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY  
T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu  
 

Bench Heat Gun PHLG600 User Manual
Bernard Welder FLX3515AM User Manual
Blackberry Cell Phone VERSION 1012 User Manual
Blodgett Convection Oven CNV14E User Manual
Blodgett Oven BCX 14E User Manual
Braun Electric Shaver 5376 User Manual
Bush Hog Compact Loader 2297 User Manual
Carrier Refrigerator 17 User Manual
Casio Home Theater System MA0612 EA User Manual
Channel Vision Computer Hardware C 0128D User Manual