Casio Digital Camera EX N1 User Manual

E
Digital Camera  
User’s Guide  
Thank you for purchasing this CASIO product.  
• Before using it, be sure to read the precautions contained in this User’s Guide.  
• Keep the User’s Guide in a safe place for future reference.  
• For the most up-to-date information about this product, visit the official EXILIM  
Website at http://www.exilim.com/  
• Illustrations in this User’s Guide are based on the EX-N1 model.  
 
Read this first!  
• The contents of this manual are subject to change without notice.  
• The contents of this manual have been checked at each step of the production  
process. Feel free to contact us if you notice anything that is questionable,  
erroneous, etc.  
• Any copying of the contents of this User’s Guide, either in part or its entirety, is  
forbidden. Except for your own personal use, any other use of the contents of this  
manual without the permission of CASIO COMPUTER CO., LTD. is forbidden  
under copyright laws.  
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost  
profits suffered by you or any third party due to the use or malfunction of this  
product.  
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages, lost  
profits, or claims by third parties arising out of the use of Photo Transport or  
YouTube Uploader for CASIO.  
• CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost  
profits caused by loss of memory contents due to malfunction, repair, or any other  
reason.  
• Note that the example screens and product illustrations shown in this User’s Guide  
may differ somewhat from the screens and configuration of the actual camera.  
LCD Panel  
The liquid crystal panel of the monitor screen uses high-precision technology that  
provides a pixel yield in excess of 99.99%. This means that some very small number  
of pixels may not light or may remain lit at all times. This is due to the characteristics  
of the liquid crystal panel, and does not indicate malfunction.  
Take a few test shots  
Before shooting your final image, shoot a test shot to ensure that the camera is  
recording correctly.  
 
3
 
Contents  
Contents  
 
4
Contents  
 
5
Selecting the Screen Aspect Ratio and  
Video Output System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Video Out) . . 99  
Contents  
 
6
Contents  
 
7
General Guide  
The numbers in parentheses indicate the pages where each item is explained.  
Front  
Back  
7 8 9 bk bl  
1 2 3 4  
[
]
[
[
]
]
[
]
[
]
SET  
bq bp bo bn bm  
6
5
Shutter button (page 25)  
Flash (page 35)  
[ON/OFF] (Power)  
(page 22)  
Front lamp (page 37)  
Microphone  
(pages 43, 74)  
Lens  
[r] (REC) button  
(pages 22, 24)  
Back lamp  
(pages 15, 16, 35)  
Zoom button  
[0] (Movie) button  
(page 42)  
Strap hole (page 2)  
[SET] button (page 31)  
[p] (PLAY) button  
(pages 22, 28)  
Control button  
([8] [2] [4] [6])  
(pages 11, 29, 31, 35,  
1
2
3
8
9
bk  
bo  
bp  
4
5
Monitor screen  
(pages 9, 11)  
bl  
bm  
bn  
bq  
6
7
[
] (Delete) button  
(page 29)  
Bottom  
Battery/memory card slots (pages 13, 20)  
[USB/AV] port (pages 14, 15, 67)  
Connector cover  
Battery cover  
Tripod hole  
br  
bs  
bt  
ck  
cl  
bt bs  
Use this hole when attaching to a tripod.  
Speaker  
cm  
cm cl ck bt bs br  
 
8
 
Monitor Screen Contents and How to Change Them  
The monitor screen uses various indicators, icons, and values to keep you informed  
of the camera’s status.  
• The sample screens in this section are intended to show you the locations of all the  
indicators and figures that can appear on the monitor screen in various modes.  
They do not represent screens that actually appear on the camera.  
. Snapshot Recording  
Remaining snapshot memory capacity  
(page 122)  
1
12345678  
Remaining movie memory capacity (page 42)  
Recording mode (page 24)  
2
9
3
co  
bk  
bl  
bm  
bn  
bo  
bp  
White balance setting (page 62)  
Continuous shutter (page 57)  
Image deterioration indicator (page 40)  
Metering mode (page 124)  
Snapshot image size (page 32)  
Snapshot image quality (page 61)  
Movie image quality (page 34)  
Flash (page 35)  
Self-timer (page 37)  
Make-up (page 38)  
Lighting (page 38)  
ISO sensitivity (page 64)  
Date/time (page 96)  
Exposure compensation (page 61)  
Focus frame (pages 26, 55)  
Timestamp indicator (page 96)  
Battery level indicator (page 17)  
Eye-Fi (page 88)  
Face Detection (page 56)  
Anti Shake (page 58)  
Focus Mode (page 52)  
4
5
6
7
8
9
bk  
bl  
bm  
bn  
bo  
bp  
bq  
br  
bs  
bt  
ck  
cl  
cm  
cn  
co  
cn  
cm  
cl  
ck  
bt bs br  
bq  
 
9
 
. Shutter Button Half-pressed  
Recording mode (page 24)  
Flash (page 35)  
ISO sensitivity (page 64)  
Aperture value  
Shutter speed  
Focus frame (pages 26, 55)  
1
1
2
3
4
5
6
2
3
4
5
6
NOTE  
• Depending on recording settings, the aperture, shutter speed, and ISO sensitivity  
values may not appear on the monitor screen. These values will be orange if the  
Auto Exposure (AE) is not correct for some reason.  
. Movie Recording  
Recording mode (page 42)  
White balance setting (page 62)  
Remaining movie memory capacity (page 42)  
Movie recording time (page 42)  
Exposure compensation (page 61)  
Battery level indicator (page 17)  
Movie recording in progress (page 42)  
1
12  
2
3
4
5
6
7
3
4
7
6
5
. Snapshot Viewing  
File type  
1
2
3
4
5
6
7
8
9
bk  
bl  
1
2
3
Protect indicator (page 73)  
Folder name/file name (page 90)  
Snapshot image quality (page 61)  
Snapshot image size (page 32)  
ISO sensitivity (page 64)  
Aperture value  
Shutter speed  
Date/time (page 96)  
Battery level indicator (page 17)  
Eye-Fi (page 88)  
4
5
6
7
8
9
bl  
bk  
 
10  
   
. Movie Playback  
File type  
1
2
3
4
5
6
7
8
1 2 3  
Protect indicator (page 73)  
Folder name/file name (page 90)  
Movie recording time (page 42)  
Movie image quality (page 34)  
Date/time (page 96)  
4
5
Battery level indicator (page 17)  
Eye-Fi (page 88)  
8
7
6
. Configuring Monitor Screen Settings  
You can turn display information on and off by pressing [8] (DISP). You can  
configure separate settings for the REC mode and PLAY mode.  
REC mode  
Information  
display on  
Displays information about image settings, etc.  
In addition to information about  
Information  
display,  
remaining movie  
memorycapacity,  
date/time on  
snapshot settings, displays  
remaining movie memory capacity  
and the date/time screen.  
• You can specify the date style you  
want to use (page 97).  
Information  
display off  
No settings or other information displayed.  
PLAY mode  
Information  
display on  
Displays settings when shooting, current date and time, and  
other information.  
Information  
display off  
No information displayed when shooting.  
 
11  
     
Quick Start Basics  
What you can do with your CASIO camera  
Your CASIO camera is packed with a powerful selection of features and functions to  
make recording of digital images easier, including the following main functions.  
Premium Auto  
Select Premium Auto recording and the  
camera automatically determines whether you  
are shooting a subject or scenery, and other  
conditions. Premium Auto delivers higher  
image quality than standard Auto.  
*See page 24 for more information.  
Make-up Function  
The Make-up Function smoothes the skin  
texture of the subject and softens facial  
shadows caused by harsh sunlight for better  
looking portraits.  
*See page 38 for more information.  
BEST SHOT  
Simply select the sample scene you want and  
the camera sets up automatically. Then all you  
need to do is press the shutter button for  
perfect images.  
*See page 46 for more information.  
Quick Start Basics  
 
12  
   
First, charge the battery prior to use.  
Note that the battery of a newly purchased camera is not charged. Perform the steps  
below to load the battery into the camera and charge it.  
• Your camera requires a special CASIO rechargeable lithium ion battery (NP-80) for  
power. Never try to use any other type of battery.  
To load the battery  
1. Open the battery cover.  
2. Load the battery.  
With the EXILIM logo on  
Stopper  
the battery facing  
downwards (in the  
direction of the lens), hold  
the stopper next to the  
battery in the direction  
indicated by the arrow as  
you slide the battery into  
the camera. Press the  
battery in until the stopper  
secures it in place.  
NG  
OK  
Battery  
EXILIM logo  
3. Close the battery cover.  
Quick Start Basics  
 
13  
     
To replace the battery  
1. Open the battery cover and  
Stopper  
remove the current battery.  
2. Load a new battery.  
Charge the Battery  
You can use either of the two following methods to charge the camera’s battery.  
• USB-AC adaptor  
• USB connection to a computer  
. To charge with the USB-AC adaptor  
The adaptor lets you charge the battery while it is loaded in the camera.  
While the camera is turned off, connect in the sequence shown below (  
,
1 2 3  
,
,
).  
4
Charging time: Approximately 120 minutes  
Power cord  
4
3
[USB/AV] port  
2
USB-AC adaptor  
1
USB cable  
(included with camera)  
Making sure that the mark on the USB cable connector is  
towards the lens side, connect the cable to the camera.  
Quick Start Basics  
 
14  
     
IMPORTANT!  
• Make sure that you insert the cable connector into the USB/  
AV port until you feel it click securely into place. Failure to  
insert the connector fully can result in poor communication or  
malfunction.  
• Note that even while the connector is fully inserted, you still  
will be able to see the metal part of the connector as shown in  
the illustration.  
Back Lamp Operation  
Back lamp  
Lamp Status  
Description  
Lit Red  
Charging  
Abnormal ambient temperature, USB-  
AC adaptor problem, or battery  
problem (page 111)  
Flashing Red  
Off  
Charging complete  
. To charge using a USB connection to a computer  
USB connection lets you  
charge the battery while it is  
loaded in the camera.  
Computer  
(power turned on)  
While the camera is turned off,  
connect in the sequence  
USB port  
shown below (  
,
). If the  
1 2  
camera is on, press [ON/OFF]  
(Power) to turn it off before  
connecting it to your computer.  
Charging time: Approximately  
140 minutes  
[USB/AV]  
port  
2
1
USB cable  
(included with camera)  
Making sure that the mark on the USB cable  
connector is towards the lens side, connect the cable  
to the camera.  
Quick Start Basics  
 
15  
       
IMPORTANT!  
• The first time you connect the camera to your computer with the USB cable, an  
error message may appear on your computer. If this happens, disconnect and then  
reconnect the USB cable.  
• Depending on the setup of your computer, you may not be able to charge the  
camera’s battery over a USB connection. If this happens, use of the USB-AC  
adaptor that comes with the camera is recommended.  
• Charging is not performed while the connected computer is in the hibernate mode.  
Back Lamp Operation  
Back lamp  
Lamp Status  
Description  
Lit Red,  
(Lit/Flashing Amber)  
Charging  
Abnormal ambient temperature,  
charging taking abnormally long, or  
Flashing Red  
Off, (Lit Green)  
Charging complete  
• The information in parentheses in the above table shows the lamp status while the  
camera is turned on during charging.  
Other Charging Precautions  
• With the two charging methods described above, you can charge the camera’s  
battery (NP-80) without removing it from the camera. You also can charge the  
battery using an optionally available charger unit (BC-80L). Never use any other  
type of charger device. Attempting to use a different charger can result in  
unexpected accident.  
• USB charging devices and power supply devices are subject to fixed standards.  
Use of an inferior device or a device that is not up to standard can cause  
malfunction and/or failure of your camera.  
• Operation is not guaranteed in the case of a computer built or modified by you.  
Even in the case of a commercially available computer, certain USB port  
specifications may make it impossible to charge via the USB cable.  
• A battery that is still warm due to normal use may not charge fully. Give the battery  
time to cool before charging it.  
• A battery discharges slightly even when it is not loaded in the camera. Because of  
this, it is recommended that you charge the battery immediately before you need to  
use it.  
• Charging the camera’s battery may cause interference with TV and radio reception.  
If this happens, plug the charger into an outlet that is further away from the TV or  
radio.  
• Actual charging time depends on current battery capacity and charging conditions.  
• Do not use the USB-AC adaptor with any other device.  
Quick Start Basics  
 
16  
 
Checking Remaining Battery Power  
As battery power is consumed, a battery indicator on the monitor screen indicates  
remaining power as shown below.  
Remaining Power  
Battery Indicator  
Indicator Color  
High  
Low  
*
*
*
*
Cyan  
*
Amber  
Red  
*
Red  
indicates battery power is low. Charge the battery as soon as possible.  
Recording is not possible when is indicated. Charge the battery immediately.  
• The level shown by the battery indicator may change when you switch between the  
REC mode and PLAY mode.  
• Leaving the camera for about 30 days with no power supplied while the battery is  
dead will cause its date and time settings to be cleared. A message telling you to  
configure time and date settings will appear the next time you turn on the camera  
after restoring power. When this happens, configure date and time settings (page  
96).  
• See page 126 for information about battery life and number of shots.  
Battery Power Conservation Tips  
• When you do not need to use the flash, select ? (Flash Off) for the flash setting  
• Enable the Auto Power Off and the Sleep features to protect against wasting  
battery power when you forget to turn off the camera (pages 97, 98).  
Quick Start Basics  
 
17  
   
Configuring Basic Settings the First Time You Turn On the  
Camera  
The first time you load a battery into the camera, a screen appears for configuring the  
display language, date, and time settings. Failure to set the date and time correctly  
will cause the wrong date and time data to be recorded with images.  
IMPORTANT!  
• A screen for language selection will not appear in step 2 of the procedure below if  
you purchased a camera intended for the Japanese market. To change the display  
language from Japanese in this case, use the procedure under “Specifying the  
Display Language (Language)” (page 97). Note that a version of this manual in the  
language you select may not be included with a camera intended for the Japanese  
market.  
• Camera models sold in certain geographic areas may not support display language  
selection.  
1. Press [ON/OFF] (Power) to turn on the  
[ON/OFF] (Power)  
camera.  
2. Use [8], [2], [4], and [6] to select  
the language you want and then press  
[SET].  
[0] (Movie)  
3. Use [8] and [2] to select a date style  
and then press [SET].  
Example: July, 10, 2015  
YY/MM/DD * 15/7/10  
DD/MM/YY * 10/7/15  
MM/DD/YY * 7/10/15  
4. Set the date and the time.  
Use [4] and [6] to select the setting you want to  
change and then use [8] and [2] to change it.  
To switch between 12-hour and 24-hour format, press  
[0] (Movie).  
5. After setting the date and time, use [4] and [6]  
to select “Apply” and then press [SET].  
6. Use [8] and [2] to select “Auto” or “Premium Auto” as the auto  
recording mode and then press [SET].  
• See page 24 for information about the auto recording modes.  
Quick Start Basics  
 
18  
   
If you make a mistake configuring display language, date, or time settings with the  
above procedure, refer to the following pages for information about how to correct  
the settings.  
– Display language: Page 97  
NOTE  
• Each country controls its local time offset and the use of summer time, and so they  
are subject to change.  
• Removing the battery from the camera too soon after configuring time and date  
settings for the first time can cause the settings to be reset to their factory defaults.  
Do not remove the battery for at least 24 hours after configuring settings.  
Preparing a Memory Card  
Though the camera has built-in memory that can be used to store images and  
movies, you probably will want to purchase a commercially available memory card for  
greater capacity. The camera does not come with a memory card. Images recorded  
while a memory card is loaded are saved to the memory card. When no memory card  
is loaded, images are saved to built-in memory.  
• For information about memory card capacities, see page 122.  
Supported Memory Cards  
– SD Memory Card (Up to 2GB)  
– SDHC Memory Card (2GB to 32GB)  
– SDXC Memory Card (32GB to 2TB)  
Use one of the above types of memory card.  
• The above are supported memory card types as of June 2012.  
• Noted memory card capacities are standard values.  
• Use only SD cards that are compliant with the SD Card Association specification.  
• This camera supports use of Eye-Fi cards.  
Quick Start Basics  
 
19  
     
To load a memory card  
1. Press [ON/OFF] (Power) to turn off  
the camera and then open the  
battery cover.  
2. Load a memory card.  
Positioning the memory card so its front  
is facing upwards (towards the monitor  
screen side of the camera), slide it into  
the card slot all the way in until you hear  
it click securely into place.  
Front  
Front  
Back  
3. Close the battery cover.  
IMPORTANT!  
• Never insert anything besides a supported memory card (page 19) into the memory  
card slot.  
• Should water or any foreign object ever get into the card slot, immediately turn off  
the camera, remove the battery, and contact your retailer or nearest CASIO  
authorized service center.  
Quick Start Basics  
 
20  
 
To replace the memory card  
Press the memory card and then release it. This  
will cause it to pop out of the memory card slot  
slightly. Pull the card out the rest of the way and  
then insert another one.  
• Never remove a card from the camera while  
the back lamp is flashing green. Doing so can  
cause the image save operation to fail and  
even damage the memory card.  
To format (initialize) a new memory card  
Format a memory card on the camera before using it for the first time.  
IMPORTANT!  
• Formatting a memory card that already has snapshots or other files on it, will delete  
its contents. Normally you do not need to format a memory card again. However, if  
storing to a card has slowed down or if you notice any other abnormality, re-format  
the card.  
• Be sure to use the camera to format a memory card. Formatting a card on a  
computer will result in a non-SD standard format, which can greatly slow down  
processing time and cause compatibility, performance, and other problems.  
• Before formatting a new Eye-Fi card to use it for the first time, copy the Eye-Fi  
Manager install files to your computer. Do this before formatting the card.  
1. Press [ON/OFF] (Power) to turn on the camera and then press [SET].  
2. Use [8] and [2] to select the second Control Panel option from the  
bottom (MENU) and then press [SET] (page 31).  
3. Use [4] and [6] to select the “Set Up” tab.  
4. Use [8] and [2] to select “Format” and then press [6].  
5. Use [8] and [2] to select “Format” and then press [SET].  
Quick Start Basics  
 
21  
 
Turning the Camera On and Off  
. To turn power on  
Pressing [ON/OFF] (Power) enters the REC mode so  
you can record images. Pressing [p] (PLAY) while in  
the REC mode enters the PLAY mode, which you can  
use to view snapshots and movies (pages 28, 65).  
• Pressing [p] (PLAY) turns on the camera and enters  
the PLAY mode.  
[ON/OFF] (Power)  
• Pressing [r] (REC) while in the PLAY mode returns  
to the REC mode.  
• Take care to ensure that nothing is restricting or  
coming into contact with the lens as it extends.  
Holding the lens with your hand so it cannot extend  
creates the risk of malfunction.  
• About 10 seconds after you press [p] (PLAY) to  
enter the PLAY mode, the lens will retract into the  
camera.  
[p] (PLAY)  
[r] (REC)  
• The Sleep function or Auto Power Off (pages 97, 98)  
will turn off power automatically if you do not perform  
any operation for a preset amount of time.  
. To turn off the camera  
Press [ON/OFF] (Power).  
NOTE  
• You also can configure the camera to turn on or off when you press [r] (REC)  
Quick Start Basics  
 
22  
 
Holding the Camera Correctly  
Your images will not come out clearly if you move the camera when you press the  
shutter button. When pressing the shutter button, be sure to hold the camera as  
shown in the illustration below, and keep it still by pressing your arms firmly against  
your sides as you shoot.  
Holding the camera still, carefully press the shutter button and take care to avoid all  
movement as the shutter releases and for a few moments after it releases. This is  
especially important when available lighting is low, which slows down the shutter  
speed.  
Horizontal  
Vertical  
Hold the camera so the flash is  
above the lens.  
NOTE  
• Take care that your fingers and the strap do not  
Flash  
cover any of the areas indicated in the illustration.  
• To protect against accidentally dropping the  
camera, attach the wrist strap and make sure it is  
around your fingers or wrist while you are  
operating the camera.  
Front lamp  
• Never swing the camera around by its strap.  
• The supplied strap is intended for use with this  
camera only. Never use it for any other purpose.  
Lens  
Microphone  
IMPORTANT!  
• Take care to ensure that your fingers are not  
blocking or are not too close to the flash. Fingers  
can cause unwanted shadows when using the  
flash.  
Quick Start Basics  
 
23  
 
Shooting a Snapshot  
To select an auto recording mode  
You can select one of two auto recording modes (Auto or Premium Auto) according to  
your digital imaging needs.  
REC Screen  
Icon Display  
Setting  
Description  
R
Auto  
This is the standard Auto recording mode.  
With Premium Auto recording, the camera  
automatically determines whether you are shooting a  
subject or scenery, and other conditions. Premium  
Auto recording delivers higher image quality than  
standard Auto recording.  
• Premium Auto recording takes longer to process  
image data after it is shot than Auto recording.  
• It also requires more power (and runs down the  
battery quicker) than Auto.  
Ÿ
Premium  
Auto  
1. Press [ON/OFF] (Power) to turn on the camera.  
The camera will enter the REC mode.  
• If the camera is in the PLAY mode, press [r] (REC).  
• You also can configure the camera to turn on when you press [r] (REC)  
2. Press [SET].  
3. Use [8] and [2] to select the top Control Panel option (Auto recording  
mode).  
Quick Start Basics  
 
24  
   
4. Use [4] and [6] to select “Auto” or “Premium Auto”, and then press  
[SET].  
This enters the selected auto recording mode.  
Auto recording mode icon  
[ON/OFF] (Power)  
Shutter button  
[r] (REC)  
[SET]  
[8] [2] [4] [6]  
Remaining Snapshot Memory  
Monitor screen  
Capacity (page 122)  
To shoot a snapshot  
1. Point the camera at the subject.  
If you are using Premium Auto, text will appear in the lower right corner of the  
monitor screen describing the type of shot the camera has detected.  
• You can zoom the image, if you want.  
w Wide Angle  
z Telephoto  
Zoom button  
Quick Start Basics  
 
25  
     
2. Half-press the shutter button to  
Back lamp  
focus the image.  
When focus is complete, the camera  
will beep, the back lamp will light  
green, and the focus frame will turn  
green.  
Focus frame  
Half-press  
Press lightly  
until the  
button stops.  
When you half-press the shutter button, the  
camera automatically adjusts exposure and  
focuses on the subject it is currently pointed at.  
Mastering how much pressure is required for a  
half-press and a full-press of the shutter button  
is an important technique for good-looking  
images.  
Beep, beep (Image is in focus.)  
3. Continuing to keep the camera still, press the shutter button the rest of  
the way down.  
This records the snapshot.  
Recording a Movie  
Full-press  
[0] (Movie)  
Press [0] (Movie) to start  
movie recording. Press  
[0] (Movie) again to stop  
movie recording. See  
page 42 for details.  
Snap (Image is recorded.)  
Quick Start Basics  
 
26  
 
. If the image does not focus...  
If the focus frame stays red and the back lamp is flashing green, it means that the  
image is not in focus (because the subject is too close, etc.). Re-point the camera at  
the subject and try to focus again.  
. Shooting with Auto  
If the subject is not in the center of the frame...  
“Focus lock” (page 53) is the name of a technique you can use when you want to  
shoot an image in which the subject to be focused on is not within the focus frame in  
the center of the screen.  
To track the movement of a moving subject  
Half-press the shutter button to follow and focus automatically on a moving subject.  
See “O Tracking” (page 55) for more information.  
. Shooting with Premium Auto  
• In addition to shutter speed, aperture, and ISO sensitivity, the camera  
automatically executes the following operation as required when shooting with  
Premium Auto.  
– Auto Focus is normally performed until you half-press the shutter button.  
– Make-up (page 38)  
Under the initial default camera setup when you purchase it, selecting Premium  
Auto as the auto recording mode (page 24) turns on the Make-up function.  
• Shooting with Premium Auto can cause vibration and noise to occur due to lens  
operation. This does not indicate malfunction.  
• When Shooting with Premium Auto, the message “Processing Premium Auto.” may  
appear on the monitor screen. If you feel the camera is taking too long to process  
data, try shooting with standard Auto instead.  
• In some cases, Premium Auto may not be able to interpret the shooting  
environment correctly. If this happens, shoot with standard Auto.  
Quick Start Basics  
 
27  
Viewing Snapshots  
Use the following procedure to view snapshots on the camera’s monitor screen.  
• For information about how to play back movies, see page 65.  
1. Press [p] (PLAY) to enter the  
PLAY mode.  
• This will display one of the snapshots  
currently stored in memory.  
• Information about the displayed  
snapshot also is included (page 10).  
• You also can clear the information to  
[p] (PLAY)  
view only the snapshot (page 11).  
• You can zoom the image by pressing  
the z zoom button (page 66). If you are recording a snapshot that is very  
important to you, it is recommended that you zoom the image and check its  
details after recording it.  
2. Use [4] and [6] to scroll between images.  
• Holding down either button scrolls at high speed.  
[6]  
[6]  
[4]  
[4]  
NOTE  
• Half-pressing the shutter button while in the PLAY mode or while a menu screen is  
displayed will switch directly to the REC mode.  
Quick Start Basics  
 
28  
   
Deleting Snapshots and Movies  
If memory becomes full, you can delete snapshots and movies you no longer need in  
order to free up storage and record more images.  
• In either the REC mode or PLAY mode, you can delete files  
simply by pressing [ ] (Delete).  
IMPORTANT!  
• Remember that a file (image) delete operation cannot be  
undone.  
• Deleting an audio snapshot (page 75) deletes both the  
snapshot and the audio file.  
[
] (Delete)  
• You cannot delete files while movie or audio recording is in progress.  
• The delete menu will not appear if you press [ ] (Delete) while “On” is selected for  
the camera’s “Ü Disabled” setting (page 99). You can delete files only while “Off”  
is selected for “Ü Disabled”.  
. To delete a single file  
1. Press [ ] (Delete).  
2. Use [4] and [6] to scroll through the files until the one  
you want to delete is displayed.  
3. Use [8] and [2] to select “Delete” and then press [SET].  
• To delete other files, repeat steps 2 and 3.  
• To exit the delete operation, press [ ] (Delete).  
. To delete specific files  
1. Press [ ] (Delete).  
2. Use [8] and [2] to select “Delete Files” and then press [SET].  
• This displays a file selection screen.  
3. Use [8], [2], [4], and [6] to move the selection boundary to the file  
you want to delete, and then press [SET].  
• This will select the check box of the currently selected file.  
4. Repeat step 3 to select other files, if you want. After you are finished  
selecting files, press [ ] (Delete).  
5. Use [8] and [2] to select “Yes” and then press [SET].  
• This deletes the files you selected.  
• To exit the delete operation, press [ ] (Delete).  
Quick Start Basics  
 
29  
   
. To delete all files  
1. Press [ ] (Delete).  
2. Use [8] and [2] to select “Delete All Files” and then press [SET].  
3. Use [8] and [2] to select “Yes” and then press [SET] to delete all files.  
This will cause the message “There are no files.” to appear.  
Snapshot Shooting Precautions  
Operation  
• Never open the battery cover while the back lamp is flashing green. Doing so can  
result in the image you just shot being saved incorrectly, damage to other images  
stored in memory, malfunction of the camera, etc.  
• If unwanted light is shining directly onto the lens, shade the lens with your hand  
when shooting an image.  
Monitor Screen when Shooting Snapshots  
• Subject brightness conditions can cause monitor screen response to slow and can  
cause digital noise in the monitor screen image.  
• The image that appears on the monitor screen is for image composition. The actual  
image will be recorded at the quality set for the image quality setting (page 61).  
Shooting Indoors under Fluorescent Lighting  
• Minute flickering of fluorescent lighting can affect the brightness or color of an  
image.  
. Auto Focus Restrictions  
• Any of the following can make proper focus impossible.  
– Solid color wall or other very low contrast subject  
– Strongly back lit subject  
– Very shiny subject  
– Blinds or other subject with a repeating horizontal pattern  
– Multiple subjects at varying distances from the camera  
– Subject in a dark location  
– Camera movement while shooting  
– Fast-moving subject  
– Subjects outside the focus range of the camera  
• If you cannot focus properly, try using focus lock (page 53) or Manual Focus (page  
52).  
Quick Start Basics  
 
30  
   
Snapshot Tutorial  
Using the Control Panel  
The Control Panel can be used to configure camera settings.  
1. In the REC mode, press [SET].  
• You can also display the control panel by pressing [2].  
Control Panel  
[8] [2] [4] [6]  
Available settings  
1
2
3
4
5
6
7
8
9
[SET]  
2. Use [8] and [2] to select the setting you want to change.  
This will select one of the Control Panel icons and display its settings.*1  
Auto recording mode (page 24)  
Snapshot image size/quality*2  
(pages 32, 61)  
Movie image quality (page 34)  
Flash (page 35)  
Make-up (page 38)  
Lighting (page 38)  
REC menu display (page 50)  
BEST SHOT scene selection  
(page 46)  
1
2
6
7
8
9
3
4
5
Self-timer (page 37)  
*1 Items displayed in the control panel depend on the recording mode.  
*2 Snapshot image quality cannot be changed using the Control Panel.  
3. Use [4] and [6] to change the setting.  
4. If you want to configure another setting, repeat steps 2 and 3.  
5. After all of the settings are the way you want, press [SET].  
This will apply the settings and return to the REC mode.  
If you selected “MENU”, the REC menu will appear.  
If you selected “BS”, the BEST SHOT scene menu will appear.  
• You can close the Control Panel by pressing [ ] (Delete).  
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial  
31  
   
NOTE  
• No icon is displayed for any Control Panel option (page 9) that is set to its initial  
default (reset) setting. An icon will appear only if you change the setting of the  
corresponding Control Panel option. The following are the initial defaults for Control  
Panel options.  
– Flash: Auto Flash  
– Self-timer: Off  
– Make-up: Off  
– Lighting: Off  
• You also can configure settings other than those listed above (page 50).  
Changing the Image Size (Size)  
. Pixels and image size  
A digital camera image is a collection of small  
dots called “pixels”. The more pixels there are  
in an image, the more detail there will be.  
However, you generally can do with fewer  
pixels when printing an image (L size) through  
a print service, attaching an image to e-mail,  
when viewing the image on a computer, etc.  
The size of an image indicates how many  
pixels it contains, and is expressed as  
Pixel  
x
horizontal pixels vertical pixels.  
Example:  
Image size  
10M  
pixels  
x
3648 2736 (Approximately 10 million pixels)  
x
2048 1536 (Approximately 3 million pixels)  
3M  
• Note that larger images have more pixels, so they take up more memory space.  
• For information about image size, image quality, and number of images that can be  
stored, see page 122.  
• For information about movie image size, see page 34.  
• For information about resizing existing snapshots, see page 73.  
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial  
32  
 
. To select the snapshot image size  
1. In the REC mode, press [SET].  
2. Use [8] and [2] to select the second Control Panel option from the top  
(Snapshot Image Size).  
3. Use [4] and [6] to select an image size and then press [SET].  
Suggested  
Print Size and  
Application  
Image Size  
(Pixels)  
REC Screen  
Icon Display  
Description  
16M  
(4608 3456)  
Poster Print  
Poster Print  
HDTV  
x
Good detail for better clarity even for  
images cropped (page 74) from the  
original  
3:2  
x
(4608 3072)  
16:9  
(4608 2592)  
x
10M  
(3648 2736)  
A3 Print  
x
Good detail  
5M  
A4 Print  
x
(2560 1920)  
Best when preserving memory  
capacity is relatively more important  
than image quality.  
3M  
3.5" ×5" Print  
E Mail  
x
(2048 1536)  
Image files are smaller, which is  
better when attaching images to e-  
mail. However, images are relatively  
coarser.  
VGA  
(640 480)  
x
• The initial factory default image size setting is “16M”.  
• Selecting “3:2” records images with an aspect ratio of 3:2, which matches the  
standard aspect ratio of print paper.  
• The letters “HDTV” stand for “High Definition Television”. An HDTV screen has an  
aspect ratio of 16:9, which makes them wider than the usual 4:3 aspect ratio of  
television screens of the past. Your camera can record images that are compatible  
with the aspect ratio an HDTV screen.  
• You should regard the print paper sizes suggested here as guidelines only (200 dpi  
print resolution).  
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial  
33  
. Specifying Movie Image Quality  
Movie image quality is a standard that determines the detail, smoothness, and clarity  
of a movie during playback. Shooting with the high-quality (HD) setting will result in  
better image quality, but it also shortens the amount of time you can shoot.  
1. In the REC mode, press [SET].  
2. Use [8] and [2] to select the third Control Panel option from the top  
(Movie Image Quality).  
3. Use [4] and [6] to select the setting you want and then press [SET].  
Image Quality  
(Pixels)  
REC Screen Approximate Data  
Icon Display Rate  
Frame Rate  
x
1280 720  
HD  
30.2 Megabits/second 30 frames/second  
10.6 Megabits/second 30 frames/second  
x
640 480  
STD  
• The 16:9 aspect ratio is available when “HD” is selected as the image quality.  
• Memory capacity (Movie recording time you can shoot) will be affected by the  
quality settings you configure (page 123).  
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial  
34  
 
Using Flash (Flash)  
1. In the REC mode, press [2] ( ) once.  
Flash  
2. Use [4] and [6] to select the flash  
setting you want and then press [SET].  
• If there are no indicators on the monitor  
screen, you can cycle through the flash  
modes by pressing [2] ( ). You can turn  
display information on or off by pressing  
[8] (DISP) (page 11).  
[2] (  
)
REC Screen  
Icon Display  
Setting  
Description  
Flash fires automatically in accordance with  
exposure (amount of light and brightness)  
conditions.  
>
?
Auto Flash  
Flash Off  
None  
Flash does not fire.  
Flash always fires. This setting can be used to  
brighten a subject that normally comes out dark  
due to daylight or backlight (daylight synchro  
flash).  
<
¥
Flash On  
Red Eye  
Flash fires automatically. This type of flash can be  
used to reduce the chance of redness in the  
subject’s eyes.  
Reduction  
3. Press the shutter button to shoot.  
Back lamp  
Flashes orange while the flash is charging to  
indicate that image recording is disabled.  
• You will not be able to take another flash  
snapshot until the lamp stops flashing  
orange, which indicates that charging is  
complete.  
< indicates the flash will fire.  
• For information about Flash Range, see page 125.  
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial  
35  
   
IMPORTANT!  
• Foreign matter on the flash window can react with the light of the flash, producing  
some smoke and abnormal odor. Though this does not indicate malfunction, oil  
from your fingers and other foreign matter when left on the flash window can  
become difficult to clean off later. Because of this, you should make it a regular  
habit to wipe the window clean regularly with a soft, dry cloth.  
NOTE  
• Take care so your fingers and the strap do not block the flash.  
• The desired effect may not be obtained when the subject is too far away or too  
close.  
• Flash charging time (page 125) depends on operating conditions (battery  
condition, ambient temperature, etc.).  
• Shooting with flash turned off when lighting is dim results in a slow shutter speed,  
which can cause image blur due to camera movement. Under such conditions,  
secure the camera with a tripod, etc.  
• With red eye reduction, the flash is fired automatically in accordance with  
exposure. It does not fire in areas where lighting is bright.  
• The presence of outdoor sunlight, fluorescent lighting, or some other light source  
can cause abnormal image colors.  
• Select ? (Flash Off) for the flash setting when shooting in areas where flash  
photograph is prohibited.  
Red-eye Reduction  
Using the flash to shoot at night or in a dimly lit room can cause red spots inside the  
eyes of people who are in the image. This is caused when the light from the flash  
reflects off of the retina of the eye. When red-eye reduction is selected as the flash  
mode, the camera fires a pre-flash to cause the irises in the eyes of any people in the  
image to close, which reduces the chance of red eye.  
Note the following important points when using red-eye reduction.  
• Red-eye reduction does not work unless the people in the image are looking  
directly at the camera (flash).  
• Red-eye reduction may not work very well if the subjects are located far away from  
the camera.  
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial  
36  
Using the Self-timer (Self-timer)  
With the Self-timer, pressing the shutter button starts a timer. The shutter is released  
and the image is shot after a fixed amount of time.  
1. In the REC mode, press [SET].  
2. Use [8] and [2] to select the fifth Control Panel option from the top  
(Self-timer).  
3. Use [4] and [6] to select the setting you want and then press [SET].  
REC Screen  
Icon Display  
Setting  
Description  
Ñ
10sec  
Self-timer  
10-second Self-timer  
2-second Self-timer  
Ì
2sec  
Self-timer  
• When shooting under conditions that slow down  
the shutter speed, you can use this setting to  
prevent image blur due to camera movement.  
Shoots three images: one image 10 seconds after  
the shutter button is pressed, and the next two  
images as soon as the camera is ready after  
shooting the previous image. How long it takes for  
the camera to get ready to shoot depends on the  
image size and quality settings, whether or not a  
memory card is loaded in the camera, and the flash  
charge condition.  
Ï
X3 Self-  
timer (Triple  
Self-timer)  
Î
Self-  
timer Off  
None  
Turns off the Self-timer.  
• The front lamp flashes while the Self-timer countdown is  
in progress.  
Front lamp  
• You can interrupt an ongoing Self-timer countdown by  
pressing [SET].  
NOTE  
• The Self-timer cannot be used together with the following features.  
CS, some BEST SHOT scenes  
• The Triple Self-timer cannot be used together with the following features.  
Movie, Make-up  
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial  
37  
 
Recording Beautiful Portraits (Make-up)  
Make-up smoothes the skin texture of the subject and softens facial shadows caused  
by harsh sunlight for better looking portraits.  
1. In the REC mode, press [SET].  
2. Use [8] and [2] to select the fourth control panel option from the  
bottom (Make-up).  
3. Use [4] and [6] to select “Make-up: On” and then press [SET].  
REC Screen  
Icon Display  
Setting  
Description  
On  
Make-up function enabled.  
½
Off  
None  
Make-up function disabled.  
4. Point the camera at the subject and shoot.  
NOTE  
• Turning on Make-up automatically turns on Face Detection (page 56).  
• Make-up cannot be used with the following functions.  
Movie recording, some BEST SHOT scenes, CS, Triple Self-timer  
Optimizing Image Brightness (Lighting)  
You can use this setting to optimize the balance between bright areas and dark areas  
when shooting images.  
1. In the REC mode, press [SET].  
2. Use [8] and [2] to select the third Control Panel option from the  
bottom (Lighting).  
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial  
38  
   
3. Use [4] and [6] to select the setting you want and then press [SET].  
REC Screen  
Icon Display  
Setting  
Description  
Performs brightness correction. When this option  
is selected, it takes longer for the image to be  
stored after the shutter button is pressed.  
Ï
On  
Ì
Off  
None  
Does not perform brightness correction.  
NOTE  
• Lighting is disabled during movie recording.  
Shooting with Zoom  
Your camera provides you with 5X optical zoom (that changes the lens focal  
distance), which can be used in combination with digital zoom (that digitally  
processes the center portion of the image to enlarge it) for total zoom capabilities of  
5X to 79.7X. The image deterioration point depends on the image size (page 41).  
1. In the REC mode, press the zoom button to zoom.  
w Wide Angle  
z Telephoto  
Zoom button  
w (Wide Angle) :Reduces the size of the subject and broadens the range.  
z (Telephoto) :Enlarges the subject and narrows the range.  
2. Press the shutter button to shoot the image.  
IMPORTANT!  
• Digital zoom is disabled while time stamping (page 96) is turned on.  
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial  
39  
 
NOTE  
• The higher the digital zoom factor, the coarser the recorded image. Note that the  
camera also has a function that lets you record using digital zoom without image  
deterioration (page 41).  
• Use of a tripod is recommended to protect against image blur due to camera  
movement when shooting with telephoto.  
• Performing a zoom operation changes the lens aperture.  
• Digital zoom only is available during movie recording. You can adjust the optical  
zoom setting before you press the shutter button to start movie recording.  
. Optical Zoom and Digital Zoom Switch Point  
Holding down z (telephoto) will zoom until the maximum optical zoom factor is  
reached. Momentarily releasing the button when it reaches the maximum and then  
pressing it again will switch to digital zoom, which you can use to set an even higher  
zoom factor.  
• During zoom, a zoom bar on the monitor screen shows the current zoom setting.  
Image deterioration indicator  
Focusing range  
(Displayed for Auto Focus, Macro Focus, and  
Manual Focus.)  
Zoom bar  
Undeteriorated image  
quality range  
Deteriorated image  
quality range  
5X to 36X  
20X to 79.7X  
1X  
Optical/digital zoom switch point  
• 5X optical zoom point  
Zoom pointer (Indicates current zoom.)  
Image deterioration  
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial  
40  
 
• The image deterioration point  
depends on the image size (page  
32). The smaller the image size,  
the higher the zoom factor you  
can use before reaching the  
image deterioration point.  
• Though digital zoom generally  
causes a deterioration of image  
quality, some digital zoom  
without image deterioration is  
possible with image sizes of  
“10M” and smaller. The range in  
which you can use digital zoom  
without image deterioration is  
indicated on the display. The  
deterioration point depends on  
the image size.  
Image  
Size  
Maximum  
Zoom Factor  
Undeteriorated  
zoom limit  
16M  
3:2  
20.0X  
5.0X  
16:9  
10M  
5M  
25.3X  
36.0X  
44.9X  
79.7X  
6.3X  
9.0X  
3M  
11.3X  
36.0X  
VGA  
Download from Www.Somanuals.com. All Manuals Search And DownSlonaapds.hot Tutorial  
41  
 
Recording Movie Images and Audio  
To record a movie  
1. Configure the quality setting for the movie (page 34).  
The length of the movie you can record will depend on the quality setting you  
select.  
2. In the REC mode, point the camera  
Remaining recording time  
at the subject and then press [0]  
[0] (Movie)  
(Movie).  
This will start recording and display Y  
on the monitor screen.  
Movie recording includes monaural  
audio.  
• Immediately after you press [0]  
(Movie), the camera will focus  
automatically on the subject in the  
center of the monitor screen. After  
this, focus is fixed while movie  
recording is in progress.  
Recording time  
3. Press [0] (Movie) again to stop recording.  
• Each movie can be up to 29 minutes long. Movie recording stops automatically  
after 29 minutes of recording. Movie recording also will stop automatically if  
memory becomes full before you stop movie recording by pressing  
[0] (Movie).  
Shooting with BEST SHOT  
With BEST SHOT (page 46), you can select the sample scene that matches the type  
of movie you are trying to shoot and the camera will change its setup accordingly, for  
beautiful movies every time. Movie Recording is disabled while certain BEST SHOT  
scenes are being used.  
Download from Www.Somanuals.com. All Manuals SearcRhecoArdnindgDMoovwienImloaagdes. and Audio  
42  
   
NOTE  
• Spending a long time using movie recording will cause the camera to become  
slightly warm to the touch. This is normal and does not indicate malfunction.  
• The camera also records audio. Note the following points when  
shooting a movie.  
– Take care that the microphone is not blocked by your fingers,  
etc.  
– Good recording results are not possible when the camera is  
too far away from what you are trying to record.  
Microphone  
– Operating camera buttons while shooting can cause button  
noise to be picked up in the audio.  
• Shooting a very bright subject can cause a vertical band or a pink cast on the  
monitor screen image. This does not indicate malfunction.  
• Using the camera’s built-in memory or certain types of memory cards can slow  
down processing speed. Whenever possible use an Ultra High-Speed Type  
memory card. Note, however, that not all operations can be guaranteed even if an  
Ultra High-Speed Type memory card is used. Certain movie quality settings can  
result in too much time being required to record data, which can result in breaks in  
the image and/or audio during playback. If this happens, the » and Y will flash  
on the monitor screen.  
• Only digital zoom can be used for zooming during movie recording. Since optical  
zoom is not possible while recording a movie, zoom as required before pressing  
[0] (Movie) to start recording.  
• The effects of camera movement in an image become more pronounced when you  
shoot close up or with a large zoom factor. Because of this, use of a tripod is  
recommended under these conditions.  
• Focus is fixed while movie recording is in progress.  
Download from Www.Somanuals.com. All Manuals SearcRhecoArdnindgDMoovwienImloaagdes. and Audio  
43  
 
Recording and Playing back Audio Only (Voice Recording)  
Voice Recording lets you record audio only, without a snapshot or movie.  
• For information about Voice Recording capacities, see page 123.  
. Recording audio only  
1. In the REC mode, press [SET].  
2. Use [8] and [2] to select the bottom Control Panel option (BS) and  
then press [SET] (page 31).  
3. Use [8], [2], [4], and [6] to select the “Voice Recording” scene and  
then press [SET].  
This causes ` to appear on the monitor screen.  
4. Press the shutter button to start recording.  
Recording time  
• The back lamp flashes green while recording is in  
progress.  
• Pressing [SET] during recording will insert a  
marker into the recording. During playback, you  
will be able to jump to the markers in the recording.  
5. Press the shutter button again to stop audio  
recording.  
Remaining recording  
• To create another audio recording file, repeat  
steps 4 and 5.  
time  
• To turn off Voice Recording, press [SET], use [8] and [2] to select the top  
Control Panel option (Auto recording mode), and then select R (Auto) or Ÿ  
(Premium Auto).  
NOTE  
• You can use [8] (DISP) during audio recording to toggle the monitor screen on  
and off.  
• When monitor screen contents are turned off, selecting the “Voice Recording”  
scene will cause the monitor screen to turn off immediately (page 11).  
About audio data  
• Audio files can be played back on a computer with Windows Media Player or  
QuickTime.  
– Audio Data: WAVE/IMA-ADPCM (WAV extension)  
Download from Www.Somanuals.com. All Manuals SearcRhecoArdnindgDMoovwienImloaagdes. and Audio  
44  
 
. To play back an audio recording  
1. In the PLAY mode, use [4] and [6] to display  
the Voice Recording file you want to play.  
` is displayed in place of an image for a Voice  
Recording file.  
2. Press [0] (Movie) to start playback.  
Voice Recording Playback Controls  
Fast forward/fast reverse  
Play/pause  
[4] [6]  
[SET]  
While playback is paused, press [4] or [6] to  
jump to the next marker and then press [SET]  
to resume playback.  
Jump to marker  
Volume adjustment  
Monitor screen on/off  
Playback end  
Press [2] and then press [8] [2]  
[8] (DISP)  
[0] (Movie)  
NOTE  
• See page 29 for information about deleting a voice recording file.  
Download from Www.Somanuals.com. All Manuals SearcRhecoArdnindgDMoovwienImloaagdes. and Audio  
45  
 
Using BEST SHOT  
BEST SHOT provides you with a collection of sample “scenes” that show a variety of  
different types of shooting conditions. When you need to change the setup of the  
camera, simply find the scene that matches what you are trying to achieve, and the  
camera sets up for it automatically. This helps to minimize the chance of ruined  
images due to poor exposure and shutter speed settings.  
. Some Sample Scenes  
Portrait  
Scenery  
Night Scene  
Night Scene Portrait  
To shoot an image with BEST SHOT  
1. In the REC mode, press [SET].  
Currently selected scene  
(with boundary)  
[8] [2] [4] [6]  
2. Use [8] and [2] to select the  
bottom Control Panel option (BS)  
and then press [SET] (page 31).  
This will display a menu of BEST  
SHOT scenes.  
• The initial default selection is  
R (Auto) or Ÿ (Premium Auto).  
Scene name  
[SET]  
3. Use [8], [2], [4], and [6] to  
move the boundary to the scene  
you want to select.  
Scene number  
• The scene menu has multiple pages. Use [8] and [2] to scroll between menu  
pages.  
• You can access information about the currently selected scene. See page 47  
for details.  
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT  
46  
     
4. Press [SET] to configure the camera with the settings for the currently  
selected scene.  
This returns to the REC mode.  
• The settings of the scene you selected remain in effect until you select a  
different scene.  
• To select a different BEST SHOT scene, repeat the above procedure from  
step 1.  
5. Press the shutter button (if you are shooting a snapshot) or [0] (Movie)  
(if you are shooting a movie).  
• To return to the auto recording mode, press [SET], use [8] and [2] to select  
the top Control Panel option (Auto recording mode), and then select R (Auto)  
or Ÿ (Premium Auto).  
. Using Scene Information Screen  
To find out more about a scene, select it with the boundary  
on the scene selection screen, and then press the z zoom  
button.  
• To return to the scene menu, press the w zoom button.  
• To scroll between scenes, use [4] and [6].  
• To configure the camera with the settings for the currently  
selected scene, press [SET].  
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT  
47  
 
. BEST SHOT Precautions  
• Some BEST SHOT scenes cannot be used while recording a movie.  
• “For YouTube” scene cannot be used while shooting a snapshot.  
• The “Voice Recording” scene cannot be used while shooting a snapshot or  
recording a movie.  
• Some scenes like “Night Scene” and “Fireworks” results in a slow shutter speed  
setting. Since a slow shutter speed increases the chance of digital noise in the  
image, the camera automatically performs a digital noise reduction process when  
either of these scenes is selected. This means that it will take a bit longer for the  
image to be saved which is indicated by the back lamp flashing green. Do not  
perform any key operation during that time. Also, it is a good idea to use a tripod to  
avoid image blur due to camera movement when shooting at slow shutter speeds.  
• The BEST SHOT YouTube scene sets up the camera for recording movies that are  
optimized for uploading to YouTube. Movies recorded with the YouTube scene are  
stored in a special folder to make them easy to locate for uploading (page 91).  
• Your camera includes a sample scene that optimizes settings for auction site  
images. Depending on your camera model, the sample scene is named either “For  
eBay” or “Auction”. Images you record using the auction site sample scene are  
stored in a special folder so you can easily find them on your computer (page 91).  
• High Sensitivity  
– The high sensitivity setting is disabled whenever the camera’s flash fires.  
– High sensitivity may not produce the desired results in very dark conditions.  
– When shooting with slow shutter speeds, use a tripod to protect against blurring  
due to camera movement.  
– Under certain lighting conditions, the camera will perform an automatic noise  
filtering operation to reduce digital noise in the image. This operation causes the  
camera to take longer than normal to save the image and be ready for the next  
shot.  
• BEST SHOT scene images were not shot using this camera.  
• Images shot using a BEST SHOT scene may not produce the results you expected  
due to shooting conditions and other factors.  
• You can modify the camera settings that are made after you select a BEST SHOT  
scene. Note, however, that the BEST SHOT settings revert to their defaults when  
you select another BEST SHOT scene or turn off the camera.  
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT  
48  
Recording a Self-portrait  
With this feature, you can shoot your own self-portrait simply by pointing the camera  
at your face.  
BEST SHOT has two self-portrait scenes from which to choose.  
• Self-portrait (1 person): Shoots when the face of at least one person, including  
you, is detected.  
• Self-portrait (2 people): Shoots when the faces of at least two people, including  
you, are detected.  
1. On the BEST SHOT scene menu, select “Self-portrait (1 person)” or  
“Self-portrait (2 people)”.  
2. Press the shutter button all the way down, and point  
the camera at yourself.  
About three seconds after you press the shutter button, the  
camera will go into Auto Shutter standby and start face  
detection. After the camera detects the specified number of  
faces, focuses, and adjusts the exposure to the proper  
level, it will beep twice and then release the shutter  
automatically.  
• The camera will emit a shutter sound and the front lamp will flash twice when  
the shutter is released.  
• To cancel Auto Shutter standby, press [SET].  
IMPORTANT!  
• If the camera remains in Auto Shutter standby without releasing the shutter, you  
can record an image by pressing the shutter button all the way down again.  
• Shooting with the self-portrait feature may produce a blurred image when shooting  
in areas where lighting is dim, which results in a very slow shutter speed setting.  
• The Auto Power Off (page 98) trigger time is fixed at five minutes while the camera  
is in Auto Shutter standby. Sleep (page 97) is disabled while Auto Shutter is being  
used.  
Download from Www.Somanuals.com. All Manuals Search And DowUnsloinagdB.EST SHOT  
49  
 
Advanced Settings  
The following are menu operations you can use to configure various camera settings.  
• REC mode menu contents and operations are different from those in the PLAY  
mode. This section explains operations using the REC menu screen. See page 69  
for information about PLAY menu screen operations.  
Using On-screen Menus  
. Example REC Menu Screen Operation  
[8] [2] [4] [6]  
1. In the REC mode, press [SET].  
2. Use [8] and [2] to select the second Control Panel  
option from the bottom (MENU) and then press  
[SET] (page 31).  
This will display the REC menu screen.  
[SET]  
3. Use [4] and [6] to select the tab where the menu  
item you want to configure is located.  
4. Use [8] and [2] to select the menu item you  
Example:  
want, and then press [6].  
When “T Quality” is  
selected on the “Quality”  
tab  
5. Use [8] and [2] to change the setting of the  
selected menu item.  
Tabs  
6. After the setting is the way you want, press  
[SET] to apply the setting and return to the  
viewfinder screen.  
• Pressing [4] instead of [SET] applies the  
selected setting and returns to the menu item  
selection.  
• To configure settings on another tab after  
pressing [4] to return to the menu item selection,  
use [8] or [ ] (Delete) to move the highlighting  
up to the tabs, and then use [4] and [6] to  
select the tab you want.  
Settings  
Selected menu item  
Advanced Settings  
 
50  
       
NOTE  
• [ ] (Delete) provides a helpful way to navigate around tabs and menus.  
– Pressing [ ] (Delete) while a tab is selected will display the viewfinder screen.  
– Pressing [ ] (Delete) while menu item or setting is selected will “back step” in  
the following sequence: Settings * Menu items * Tab.  
• Depending on the recording mode, some of the items on the menu that appears  
may not be usable.  
. REC Menu Operations in This Manual  
REC menu operations are represented in this manual as shown below. The following  
operation is the same one described under “Example REC Menu Screen Operation”  
Use [8] and [2] to select the second Control Panel option from the  
bottom (MENU) and then press [SET].  
Use [4] and [6] to select the  
“Quality” tab.  
Procedure  
[r] (REC) * [SET] * MENU * “Quality” Tab * T Quality  
Use [8] and [2] to select “T Quality”  
and then press [6].  
Press  
[r] (REC).  
Press  
[SET].  
Advanced Settings  
 
51  
REC Mode Settings (REC)  
Selecting a Focus Mode (Focus)  
Procedure  
[r] (REC) * [SET] * MENU * “REC” Tab * Focus  
• Auto Focus is the only focus mode available while face detection is enabled. To  
select another focus mode, first turn off face detection (page 56).  
Approximate Focus  
REC  
Screen  
Icon  
Focus Mode  
Snap-  
Range*1  
Settings  
Type of Shot  
Movies  
Snapshot  
Movies  
Display  
shot  
10 cm to 9  
(infinity)  
(3.9" to 9)  
(Wide Angle)*2  
Q Auto  
Focus  
General  
recording  
None  
Fixed  
focal  
point  
Fixed  
Auto-  
matic  
distance  
2
*
10 cm to 50 cm  
(3.9" to 19.7")  
(Wide Angle)*2  
´
Macro  
Close ups  
Scenery and  
other distant  
subjects  
)
Infinity  
Fixed  
Infinity  
W
Manual  
Focus  
When you  
want to focus  
manually  
10 cm to 9 (infinity)  
(3.9" to 9) (Wide Angle)*2  
Manual  
*1 The focus range is the distance from the lens surface.  
*2 Range is affected by optical zoom.  
Advanced Settings  
 
52  
     
To focus with manual focus  
1. On the monitor screen, compose the image so  
the subject you want to focus on is within the  
yellow boundary.  
2. Watching the image on the monitor screen use  
[4] and [6] to adjust focus.  
• At this time the image that is within the boundary  
will enlarge and fill the monitor screen, which aids  
in focusing. If you do not perform any operation for  
two seconds while the enlarged image is displayed,  
the screen in step 1 will re-appear.  
Yellow boundary  
NOTE  
• An Auto Macro feature detects how far the subject is from the lens and  
automatically selects either Macro Focus or Auto Focus accordingly.  
• Auto Macro can be used when recording snapshots only.  
• Use of the flash together with Macro Focus can cause the light of the flash to  
become blocked, which may result in unwanted lens shadows in your image.  
• Whenever you perform an optical zoom operation while shooting with Auto Focus,  
Macro Focus, or Manual Focus, a value will appear on the monitor screen to tell  
you the focus range, as shown below.  
Example: oo* cm to 9  
* oo is the actual focusing range value.  
• The operations assigned to the [4] and [6] keys with the “L/R Key” setting (page  
59) are disabled while Manual Focus is selected as the focus mode.  
Using Focus Lock  
Subject to  
be focused on  
“Focus lock” is a technique you can use when you want  
to compose an image in which the subject you want to  
focus on is not within the focus frame in the center of the  
screen.  
• To use focus lock, select “U Spot” for the Auto  
Focus area (page 55).  
1. Align the monitor screen’s focus frame with  
the subject you want to focus on and then  
half-press the shutter button.  
Focus frame  
Advanced Settings  
 
53  
   
2. Keeping the shutter button half-pressed  
(which maintains the focus setting), move the  
camera to compose the image.  
3. When you are ready to shoot the image,  
press the shutter button the rest of the way  
down.  
NOTE  
• Focus lock also locks exposure (AE).  
Changing the Focus Frame Shape (Focus Frame)  
Procedure  
[r] (REC) * [SET] * MENU * “REC” Tab * Focus Frame  
You can use this procedure to select from among five different shapes, including a  
heart shape, for the focus frame.  
Settings  
ß
¹
¬
μ
NOTE  
• Half-pressing the shutter button will cause the focus frame to change one of the  
shapes shown below.  
Focus successful  
Focus not successful  
• When shooting with face detection, the frame shape is ß.  
Advanced Settings  
 
54  
 
Specifying the Auto Focus Area (AF Area)  
Procedure  
[r] (REC) * [SET] * MENU * “REC” Tab * AF Area  
This mode takes readings of a small area in the center of the  
image. This setting works well with focus lock (page 53).  
U
I
O
Spot  
When you half-press the shutter button while this setting selected,  
the camera will select the optimum Auto Focus area from among  
nine possible areas. The focus frame of the area where the  
camera focuses will be displayed in green.  
Multi  
Half-pressing the shutter button focuses on the subject and  
causes the focus frame to track the movement of the subject.  
Tracking  
I Multi”  
U Spot” or O Tracking”  
Focus frame  
Focus frame  
IMPORTANT!  
• Auto Focus is disabled when W (Manual Focus) or ) (Infinity) is selected for the  
focus mode (page 52), even if you select an AF area.  
• Selecting O Tracking” can cause vibration and noise to occur due to lens  
operation while tracking a subject. This does not indicate malfunction.  
Advanced Settings  
 
55  
   
Using Face Detection (Face Detection)  
Procedure  
[r] (REC) * [SET] * MENU * “REC” Tab * Face Detection  
When shooting people, the face detection feature detects the faces of up to ten  
individuals and adjusts focus and brightness accordingly.  
1. Use [8] and [2] to select “On” and then press [SET].  
2. Point the camera at the subject(s).  
The camera will detect human faces and display a  
frame around each one.  
3. Half-press the shutter button.  
The camera will focus and the frames around the  
faces it focuses on will turn green.  
Face Detection icon  
4. Press the shutter button the rest of the way  
down.  
IMPORTANT!  
• The camera performs center focus if it cannot detect a face.  
• The only focus mode available while face detection is enabled is Auto Focus (AF).  
• Face detection may take a bit longer when you hold the camera sideways.  
• Detection of the following types of faces is not supported.  
– Face that is obstructed by hair, sunglasses, a hat, etc., or a face in dark shade  
– A profile or a face that is at an angle  
– A face that is very far away and small, or very close and large  
– A face in an area that is very dark  
– The face of a pet or some other non-human subject  
• Face detection cannot be used in combination with any of the following features.  
– Some BEST SHOT scenes  
– Movie Recording  
• The AF area setting (page 55) is ignored while face detection is enabled.  
• Turning on Make-up (page 38) automatically turns on Face Detection.  
Advanced Settings  
 
56  
 
Using Continuous Shutter (CS)  
Procedure  
[r] (REC) * [SET] * MENU * “REC” Tab * CS  
While Continuous Shutter is turned on, images are continually recorded until memory  
becomes full, as long as you keep the shutter button depressed.  
Releasing the shutter button stops shooting.  
NOTE  
• With continuous shutter, exposure and focus for the first image are applied for  
successive images as well.  
• Continuous shutter cannot be used in combination with any of the following.  
– Premium Auto  
– Make-up  
– Some BEST SHOT scenes  
– Movie Recording  
– Self-timer  
• When using a continuous shutter mode, keep the camera still until all recording is  
finished.  
• The continuous shutter rate depends on the current image size and image quality  
settings.  
• The speed of Continuous Shutter depends on the type of memory card loaded in  
the camera and the amount of free space available for storage. When shooting to  
built-in memory, continuous shutter shooting is relatively slow.  
Advanced Settings  
 
57  
 
Reducing the Effects of Camera and Subject Movement  
(Anti Shake)  
Procedure  
[r] (REC) * [SET] * MENU * “REC” Tab * Anti Shake  
You can turn on the camera’s Anti Shake feature to reduce image blur due to subject  
movement or camera movement when shooting a moving subject using telephoto,  
when shooting a fast-moving subject, or when shooting under dim lighting conditions.  
REC Screen  
Icon Display  
Setting  
On  
Description  
Minimizes the effects of hand and subject  
movement.  
Off  
None  
Turns off Anti Shake settings  
NOTE  
• ISO sensitivity, aperture, and shutter speed do not appear on the monitor screen  
when you half-press the shutter button while “On” is selected. These values will  
appear briefly, however, in the preview image that is displayed immediately after  
you shoot a snapshot.  
• If the flash fires, the Anti Shake icon S will remain on the display, even though  
Anti Shake does not function during flash photography.  
• The ISO sensitivity setting (page 64) must be “Auto” for Anti Shake to work.  
• Shooting with Anti Shake can cause an image to appear somewhat coarser than  
normal and can cause slight deterioration of image resolution.  
• Anti Shake may not be able to eliminate the effects of camera or subject movement  
when movement is severe.  
• Anti Shake is disabled during movie recording.  
Advanced Settings  
 
58  
 
Assigning Functions to the [4] and [6] Keys (L/R Key)  
Procedure  
[r] (REC) * [SET] * MENU * “REC” Tab * L/R Key  
You can assign one of the four functions listed below to the [4] and [6] keys.  
Setting  
EV Shift  
White Balance  
ISO  
[4]/[6] key operation  
Adjusts the EV shift value (page 61).  
Changes the white balance setting (page 62).  
Changes the ISO Sensitivity setting (page 64).  
Sets the self-timer time (page 37).  
Self-timer*  
Off  
Cancels [4] and [6] key assignments.  
* While Make-up is turned on, you will be able to use the [4] and [6] keys to select  
one of the following settings: 10sec Self-timer, 2sec Self-timer, Self-timer Off. Note  
that you will not be able to configure the self-timer setting with the [4] and [6] keys  
while Continuous Shutter (CS) is turned on.  
NOTE  
• The “L/R Key” setting cannot be used together with the following features.  
– Some BEST SHOT scenes  
Displaying the On-screen Grid (Grid)  
Procedure  
[r] (REC) * [SET] * MENU * “REC” Tab * Grid  
The on-screen grid can be displayed on the REC mode  
monitor screen for easy vertical and horizontal alignment  
when composing images.  
Advanced Settings  
 
59  
   
Using Icon Help (Icon Help)  
Procedure  
[r] (REC) * [SET] * MENU * “REC” Tab * Icon Help  
While Icon Help is turned on, a textual description will appear on the display for  
certain icons when you switch between REC functions.  
Functions Supported by Icon Help  
• REC Mode, Flash, White Balance, Self-timer, EV Shift  
Configuring Power On Default Settings (Memory)  
Procedure  
[r] (REC) * [SET] * MENU * “REC” Tab * Memory  
When you turn off the camera, it remembers the current settings of all enabled  
memory items and restores them when you turn it back on. Any memory item that is  
disabled will be returned to its initial default setting whenever you turn off the camera.  
Setting  
b BEST SHOT  
Flash  
Disabled (Initial Default Setting)  
Enabled  
Last used auto recording mode  
Auto  
Focus  
AF (Auto Focus)  
White Balance  
ISO  
Auto  
Auto  
Spot  
Off  
Setting at power  
off  
AF Area  
CS  
Self-timer  
Off  
Position before manual focus was  
selected.  
MF Position  
Zoom Position*  
Full wide  
* Optical zoom setting only.  
• If you turn the camera power off and then back on while the BEST SHOT memory  
item is enabled, all of the other memory items (except for zoom position) are  
initialized to the currently selected BEST SHOT sample scene setup, regardless of  
the enabled/disabled status of the other memory items. This is true for all BEST  
SHOT scenes.  
Advanced Settings  
 
60  
   
Image Quality Settings (Quality)  
Specifying Snapshot Image Quality (T Quality (Snapshot))  
Procedure  
[r] (REC) * [SET] * MENU * “Quality” Tab *  
T Quality (Snapshot)  
REC Screen Icon  
Display  
Setting  
Fine  
Description  
Gives image quality priority.  
Normal  
Normal  
• The “Fine” setting helps to bring out details when shooting a finely detailed image  
of nature that includes dense tree branches or leaves, or an image of a complex  
pattern.  
• Memory capacity (the number of images you can record) will be affected by the  
quality settings you configure (page 122).  
Correcting Image Brightness (EV Shift)  
Procedure  
[r] (REC) * [SET] * MENU * “Quality” Tab * EV Shift  
You can manually adjust an image’s exposure value (EV value) before shooting it.  
• Exposure Compensation Range: –2.0 EV to +2.0 EV  
• Unit: 1/3 EV  
1. Use [8] and [2] to adjust the exposure compensation value.  
[8] :Increases the EV value. A higher EV  
value is best for light-colored subjects  
and backlit subjects.  
[2] :Decreases the EV value. A lower EV  
value is best for dark-color subjects and  
for shooting outdoors on a clear day.  
To cancel exposure compensation, change the EV value to 0.0.  
Advanced Settings  
 
61  
       
2. Press [SET].  
This applies the exposure compensation value. The exposure compensation  
value you set remains in effect until you change it or turn off the camera (which  
causes it to revert to “0.0”).  
NOTE  
• When shooting under very dark or very bright conditions, you may not be able to  
obtain satisfactory results even after performing exposure compensation.  
Controlling White Balance (White Balance)  
Procedure  
[r] (REC) * [SET] * MENU * “Quality” Tab * White Balance  
You can adjust white balance to match the source of light available where you are  
shooting and avoid the blue cast that results when shooting outdoors when it is  
cloudy, and the green cast that results when shooting under fluorescent lighting.  
REC Screen  
Icon Display  
Setting  
Auto  
Description  
Configures the camera to adjust white balance  
automatically.  
None  
¤
'
(Daylight)  
(Overcast)  
(Shade)  
For shooting outdoors on a clear day  
For shooting outdoors on an overcast rainy day, in  
the shade, etc.  
For shooting on a clear day in the shade of trees or  
buildings  
(DayWhite  
Fluorescent)  
For shooting under white or day white fluorescent  
lighting  
(Daylight  
Fluorescent)  
For shooting under daylight fluorescent lighting  
For shooting under light bulb lighting  
«
(Tungsten)  
Advanced Settings  
 
62  
 
REC Screen  
Icon Display  
Setting  
Manual  
Description  
For configuring the camera manually to suit a  
particular light source  
Select “Manual”.  
Blank white paper  
1
2
Under the lighting conditions  
you plan to use when  
shooting, point the camera at  
a blank white piece of paper  
so it fills the entire monitor  
screen and then press the  
shutter button.  
Press [SET].  
3
The white balance setting is retained even if you  
turn off the camera.  
• When “Auto” is selected for the white balance setting, the camera automatically  
determines the white point of the subject. Certain subject colors and light source  
conditions can cause problems when the camera tries to determine the white point,  
which makes proper white balance adjustment impossible. If this happens, select  
the white balance setting that matches your shooting conditions (Daylight,  
Overcast, etc.).  
Advanced Settings  
 
63  
Specifying ISO Sensitivity (ISO)  
Procedure  
[r] (REC) * [SET] * MENU * “Quality” Tab * ISO  
ISO sensitivity is a measure of sensitivity to light.  
REC Screen  
Icon Display  
Setting  
Description  
Auto  
None  
Adjusts sensitivity automatically according to conditions.  
Lower  
sensitivity  
Slow shutter speed Less noise  
ISO 64  
ISO 100  
ISO 200  
ISO 400  
ISO 800  
ISO 1600  
Some coarseness  
(increased digital  
noise)  
Fast shutter speed  
(Set for shooting in  
dimly lit areas.)  
Higher  
sensitivity  
• “Auto” ISO sensitivity always is applied for movies, regardless of the current ISO  
sensitivity setting.  
• Higher ISO sensitivity values tend to result in digital noise in images.  
Using Built-in Color Filters (Color Filter)  
Procedure  
[r] (REC) * [SET] * MENU * “Quality” Tab * Color Filter  
Settings: Off, B/W, Sepia, Red, Green, Blue, Yellow, Pink, Purple  
Advanced Settings  
 
64  
   
Viewing Snapshots and Movies  
Viewing Snapshots  
See page 28 for the procedure for viewing snapshots.  
Viewing a Movie  
1. Press [p] (PLAY) and then use [4] and [6] to display the movie you  
want to view.  
2. Press [0] (Movie) to start  
Movie icon: »  
playback.  
Recording time  
Image quality  
Movie Playback Controls  
[4] [6]  
Fast forward/  
fast reverse  
• Each press of either button increases the speed of the fast  
forward or fast reverse operation.  
• To return to normal playback speed, press [SET].  
Play/pause  
[SET]  
1 frame forward/ [4] [6]  
back  
• Holding down either button scrolls continuously.  
Press [2] and then press [8] [2].  
• Volume can be adjusted only while movie playback is in  
progress.  
Volume  
adjustment  
Information  
display on/off  
[8] (DISP)  
Press the z ([) zoom button.  
• You can use [8], [2], [4], and [6] to scroll the zoomed  
image on the monitor screen. You can zoom a movie image  
up to 4.5 times normal size.  
Zoom  
Stop playback  
[0] (Movie)  
• Playback may not be possible for movies not recorded with this camera.  
Viewing Snapshots and Movies  
 
65  
         
Zooming an On-screen Image  
1. In the PLAY mode, use [4] and [6] to scroll through the images until  
the one you want is displayed.  
2. Press the z zoom button to zoom the display  
Zoom factor  
image.  
Image area  
You can use [8], [2], [4], and [6] to scroll the  
zoomed image on the monitor screen. Press the w  
zoom button to unzoom the display image.  
– When monitor screen contents are turned on, a  
graphic in the lower right corner of the screen  
shows what part of the zoomed image is  
currently displayed.  
– To exit the zoom screen, press [ ] (Delete).  
– Though the maximum image zoom factor is 8X,  
certain image sizes may not allow zooming up  
to the full 8X.  
Current display area  
Displaying the Image Menu  
1. In the PLAY mode, press the w zoom button.  
Boundary  
Use [8], [2], [4] and [6] to move the selection  
boundary around the image menu.  
To view a particular image, use [8], [2], [4], or [6] to  
move the selection boundary to the image you want  
and then press [SET].  
Viewing Snapshots and Movies  
 
66  
       
Viewing Snapshots and Movies on a TV Screen  
1. Use an optionally available AV cable (EMC-7A) to connect it to the TV.  
White  
Yellow  
Video Audio  
TV  
AV cable  
[USB/AV]  
port  
AUDIO IN jacks (white)  
VIDEO IN jack (yellow)  
• For details about connecting to the camera and precautions when connecting,  
see page 15.  
2. Turn on the TV and select its video input mode.  
If the TV has more than one video input, select the one where the camera is  
connected.  
3. Press [p] (PLAY).  
This will cause an image to appear on the TV screen, without anything appearing  
on the camera’s monitor screen.  
• You also can change the aspect ratio of the screen and the video output  
system (page 99).  
4. Now you can display images and play back movies as you normally do.  
NOTE  
• Audio is monaural.  
• Certain TVs may cut off part of the images.  
• All icons and indicators that appear on the monitor screen also appear on the TV  
screen. You can use [8] (DISP) to change the display contents.  
Viewing Snapshots and Movies  
 
67  
   
Recording Camera Images to a DVD Recorder or Video Deck  
Use one of the following methods to connect the camera to the recording device  
using an optionally available AV cable (EMC-7A).  
– DVD recorder or video deck: Connect to the VIDEO IN and AUDIO IN terminals.  
– Camera: USB/AV port  
You can play a slideshow of snapshots and movies on the camera and record it on a  
DVD or video tape. When recording images to an external device, use [8] (DISP) to  
clear all indicators from the monitor screen (page 11).  
For information about connecting a monitor to the recording device and about how to  
record, see the user documentation that comes with the recording device you are  
using.  
Viewing Snapshots and Movies  
 
68  
Other Playback Functions (PLAY)  
This section explains menu items that you can use to configure settings and perform  
other playback operations.  
Using the PLAY Panel  
Pressing [SET] in the PLAY mode will display the PLAY Panel.  
. Example PLAY Panel Operation  
1. In the PLAY mode, press [SET].  
[8] [2]  
PLAY Panel  
The PLAY Panel will appear along the  
right side of the monitor screen.  
2. Use [8] and [2] to select the  
PLAY Panel item you want, and  
then press [SET].  
[SET]  
3. The following describes the operations you can perform for each of the  
PLAY Panel items.  
â
Exit  
Exits the PLAY Panel.  
The operation that is performed when this item is selected  
depends on the type of file that is currently displayed on the  
monitor screen.  
• Movie: Starts movie playback (page 65).  
• Voice recording: Starts voice recording playback (page 45).  
• Audio snapshot: Starts audio playback (page 75).  
P
Playback  
Start  
ä
Displays a slideshow menu. See “Playing a Slideshow on the  
Slideshow Camera (Slideshow)” (page 71) for slideshow menu operations.  
Displays a rotation menu screen. See “Rotating an Image  
(Rotation)” (page 72) for details about the rotation operation.  
ÿ
Rotation  
Other Playback Functions (PLAY)  
 
69  
       
Displays the PLAY menu. You can perform the following  
operations on the PLAY menu.  
Use [4] and [6] to select the tab  
where the menu item you want to  
configure is located.  
1
Tabs  
Use [8] and [2] to select the menu  
item you want, and then press [6].  
Use [8] and [2] to change the  
setting of the selected menu item.  
Press [SET] to apply the setting.  
2
3
4
à
Menu  
Selected menu item  
NOTE  
• Pressing [ ] (Delete) performs one of the following  
operations.  
– If you previously selected a tab, pressing [ ] (Delete)  
returns to the viewfinder screen.  
– If you previously selected menu item, pressing [ ] (Delete)  
returns to the tab.  
. PLAY Menu Operations in This Manual  
PLAY menu operations are represented in this manual as shown below. The following  
operation is the same one described under “Example PLAY Panel Operation” on  
Use [8] and [2] to select the bottom PLAY Panel  
item (MENU) and then press [SET].  
Procedure  
[p] (PLAY) * [SET] * MENU * “PLAY” Tab * Protect  
Press  
Press [SET].  
Use [4] and [6] to select the  
[p] (PLAY).  
“PLAY” tab.  
Use [8] and [2] to select  
“Protect” and then press [6].  
Other Playback Functions (PLAY)  
 
70  
Playing a Slideshow on the Camera (Slideshow)  
1. In the PLAY mode, press [SET].  
2. Use [8] and [2] to select the third PLAY Panel item from the bottom  
(Slideshow) and then press [SET] (page 69).  
Start  
Time  
Starts the slideshow.  
Time from the start to the end of the slideshow  
1 to 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes  
Amount of time each image remains displayed  
Use [4] and [6] to select a value from 1 to 30 seconds, or “MAX”.  
If you specify a value from 1 to 30 seconds, images change at the  
specified interval, but the audio portion of movies and audio  
snapshots will continue to play until the end.  
When the slideshow reaches a movie file while “MAX” is selected,  
only the first frame of the movie will displayed. Voice Recording  
files are not played back when “MAX” is selected.  
Interval  
Effect  
Turns effect on or off.  
On: Turns on the image change effect and background music.  
Off: No image change effect or background music  
• To stop the slideshow, press [ ] (Delete). Pressing [SET] instead of  
] (Delete) stops the slideshow and returns to the menu screen.  
[
• Adjust audio volume by pressing [2] and then press [8] or [2] during  
playback.  
• All button operations are disabled while the slideshow is transitioning from one  
image to another.  
• The time required for transition from one image to another may be longer in the  
case of an image that was not recorded with this camera.  
Other Playback Functions (PLAY)  
 
71  
 
Rotating an Image (Rotation)  
1. In the PLAY mode, display the snapshot you want to rotate.  
2. Press [SET].  
3. Use [8] and [2] to select the second PLAY Panel item from the bottom  
(Rotation) and then press [SET] (page 69).  
4. Use [8] and [2] to select “Rotation” and then press [SET].  
Each press of [SET] will rotate the displayed image 90 degrees left.  
5. When the displayed image is at the orientation you want, press  
[
] (Delete).  
NOTE  
• Note that this procedure does not actually change the image data. It simply alters  
how the image is displayed on the camera’s monitor screen.  
• An image that has been protected or zoomed cannot be rotated.  
• The original (unrotated) version of the image will be displayed on the image menu  
screen.  
Selecting Images for Printing (DPOF Printing)  
Procedure  
[p] (PLAY) * Snapshot Screen * [SET] * MENU *  
“PLAY” Tab * DPOF Printing  
See page 77 for details.  
Other Playback Functions (PLAY)  
 
72  
   
Protecting a File Against Deletion (Protect)  
Procedure  
[p] (PLAY) * [SET] * MENU * “PLAY” Tab * Protect  
Protects specific files.  
Use [4] and [6] to scroll through the files  
until the one you want to protect is  
displayed.  
1
Use [8] and [2] to select “On” and then  
press [SET].  
2
On  
An image that is protected is indicated by  
the icon.  
To protect other files, repeat steps 1 and 2.  
To exit the protect operation, press [ ] (Delete). To unprotect a file,  
select “Off” instead of “On” in step 2 above.  
3
Protects all files.  
Use [8] and [2] to select “All Files: On” and then press [SET].  
Press [ ] (Delete).  
To unprotect all files, select “All Files: Off” instead of “All Files: On” in  
step 1 above.  
1
2
All Files:  
On  
IMPORTANT!  
• Note that even if a file is protected, it will be deleted if you perform the format  
operation (page 100).  
Resizing a Snapshot (Resize)  
Procedure  
[p] (PLAY) * Snapshot Screen * [SET] * MENU *  
“PLAY” Tab * Resize  
You can reduce the size of a snapshot and save the result as a separate snapshot.  
The original snapshot is also retained. You can select resize an image to one of three  
image sizes: 10M, 5M, VGA.  
• Resizing a 3:2 or 16:9 size snapshot will create an image with an aspect ratio of  
4:3, with both sides cut off.  
• The recording date of the resized version of the snapshot will be the same as the  
recording date of the original snapshot.  
Other Playback Functions (PLAY)  
 
73  
       
Cropping a Snapshot (Trimming)  
Procedure  
[p] (PLAY) * Snapshot Screen * [SET] * MENU *  
“PLAY” Tab * Trimming  
You can crop a snapshot to trim parts you do not need, and  
save the result in a separate file. The original snapshot is  
also retained.  
Zoom factor  
Represents  
snapshot area  
Use the zoom button to zoom the image to the size you  
want, use [8], [2], [4], and [6] to display the portion of the  
image you want to cut out, and then press [SET].  
• The image produced by cropping a 3:2 or 16:9 image will  
have an aspect ratio of 4:3.  
• The recording date of the cropped image will be the  
same as the recording date of the original snapshot.  
Part of snapshot that is  
currently displayed  
Adding Audio to a Snapshot (Dubbing)  
Procedure  
[p] (PLAY) * Snapshot Screen * [SET] * MENU *  
“PLAY” Tab * Dubbing  
You can add audio to a snapshot after you shoot it.  
You can re-record a snapshot’s audio whenever you  
want. You can record up to about 30 seconds of audio  
for a single snapshot.  
1. Press [SET] to start audio recording.  
Remaining recording time  
Other Playback Functions (PLAY)  
 
74  
       
2. Press [SET] again to stop audio recording.  
• Take care that you do not block the camera’s microphone  
with your fingers while recording.  
• Good recording results are not possible when the camera is  
too far away from what you are trying to record.  
• Your camera supports the following audio data formats.  
– Audio Format: WAVE/IMA-ADPCM (WAV extension)  
• You cannot add audio to an image that is protected.  
• To delete audio, perform the following operation:  
Dubbing * Delete * [SET] * [ ] (Delete).  
Microphone  
IMPORTANT!  
• Note that you cannot restore the original audio of an Audio Snapshot after you  
delete or re-record it.  
. To play snapshot audio  
1. In the PLAY mode, use [4] and [6] to scroll through the images until  
the Audio Snapshot you want is displayed.  
An audio snapshot is one that has a ˆ icon.  
2. Press [0] (Movie) to start playback.  
Voice Recording Playback Controls  
Fast forward/fast reverse  
Play/pause  
[4] [6]  
[SET]  
Press [2] and then  
press [8] [2].  
Volume adjustment  
Display content switching  
Stop playback  
[8] (DISP)  
[0] (Movie)  
• Audio of an Audio Snapshot also can be played back on a computer with Windows  
Media Player or QuickTime.  
Other Playback Functions (PLAY)  
 
75  
   
Copying Files (Copy)  
Procedure  
[p] (PLAY) * [SET] * MENU * “PLAY” Tab * Copy  
Files can be copied from the camera’s built-in memory to a memory card or from a  
memory card to built-in memory.  
Copies all files from built-in camera memory to a memory card.  
Built-in * Card This option copies all the files in built-in camera memory. It  
cannot be used to copy a single file.  
Copies a single file on the memory card to camera built-in  
camera memory. Files are copied to the folder in built-in  
Card * Built-in memory whose name has the largest serial number.  
Use [4] and [6] to select the file you want to copy.  
Use [8] and [2] to select “Copy” and then press [SET].  
1
2
NOTE  
• You can copy snapshots, movies, audio snapshots, or Voice Recording files you  
recorded with this camera.  
Other Playback Functions (PLAY)  
 
76  
 
Printing  
Printing Snapshots  
Professional Print Service*  
You can take a memory card that contains the images you want  
to print to a professional print service and have them printed.  
Printing on a Home Printer*  
You can use a printer equipped with a memory card slot to print  
images directly from a memory card. For details, see the user  
documentation that comes with your printer.  
Printing with a Computer  
After transferring the images to your computer, use  
commercially available software to print.  
* You can specify which images you want to print, the number of copies, and date  
stamp settings before printing (page 77).  
Using DPOF to Specify Images to be Printed and the Number  
of Copies  
. Digital Print Order Format (DPOF)  
DPOF is a standard that allows you to include image type, number of copy,  
and time stamp on/off information on the memory card with the images.  
After configuring settings, you can use the memory card to print on a home  
printer that supports DPOF or take the memory card to a professional print  
service.  
• Whether or not you will be able to use DPOF settings for printing depends on the  
printer you are using.  
• Some professional print services may not support DPOF.  
Printing  
 
77  
     
. Configuring DPOF Settings Individually for Each Image  
Procedure  
[p] (PLAY) * Snapshot Screen * [SET] * MENU *  
“PLAY” Tab * DPOF Printing * Select images  
1. Use [4] and [6] to scroll through the files until the image you want to  
print is displayed.  
2. Use [8] and [2] to specify the number of copies.  
You can specify a value up to 99. Specify 00 if you do not want to print the image.  
• If you want to include the date in the images, press [0] (Movie) so “On” is  
shown for date stamping.  
• Repeat steps 1 and 2 to configure settings for other images, if you want.  
3. Press [SET].  
. Configuring the Same DPOF Settings for All the Images  
Procedure  
[p] (PLAY) * Snapshot Screen * [SET] * MENU *  
“PLAY” Tab * DPOF Printing * All images  
1. Use [8] and [2] to specify the number of copies.  
You can specify a value up to 99. Specify 00 if you do not want to print the image.  
• If you want to include the date in the images, press [0] (Movie) so “On” is  
shown for date stamping.  
2. Press [SET].  
DPOF settings are not cleared automatically after printing is complete.  
The next DPOF print operation you execute will be performed using the last DPOF  
settings you configured for the images. To clear DPOF settings, specify “00” for the  
number of copies of all images.  
Tell your print service about your DPOF settings!  
If you take a memory card to a professional print service, be sure to tell them that it  
includes DPOF settings for the images to be printed and the number of copies. If you  
don’t, the print service may print all the images without regard to your DPOF settings,  
or they may ignore your date stamp setting.  
Printing  
 
78  
. Date Stamping  
You can use one of the following three methods to include the recording date in the  
printout of an image.  
Configuring camera settings  
Configure DPOF settings (page 77).  
You can turn date stamping on and off each time you print. You can configure  
settings so some images include the date stamp and some don’t.  
Configure the Camera’s Time Stamp setting (page 96).  
• The camera’s Time Stamp setting imprints the date into a snapshot when you  
shoot it, so the date is always included when you print. It cannot be deleted.  
• Do not turn on DPOF date stamping for an image that includes a date  
stamped with the camera’s Time Stamp function. Doing so can cause the two  
stamps to be overprinted.  
Configuring computer settings  
You can use commercially available image management software to date  
stamp images.  
Professional print service  
Request date stamping when ordering prints from a professional print service.  
. Standards Supported by the Camera  
• Exif Print  
Printing on a printer that supports Exif Print uses information  
about shooting conditions recorded with the image to enhance  
printed image quality. Contact your printer manufacturer for  
information about models that support Exif Print, printer upgrades, etc.  
Printing  
 
79  
 
Using the Camera with a Computer  
Things you can do using a computer...  
You can perform the operations described below while the camera is connected to a  
computer.  
Save images to a  
computer and  
view them there  
• Save images and view them manually  
(USB connection) (pages 82, 86).  
• Transfer images to a computer  
automatically over a wireless LAN for  
viewing (Eye-Fi) (page 88).  
Play back and  
edit movies  
• You can play back movies (pages 84, 87).  
• To edit movies, use commercially  
available software as required.  
Transfer images  
stored on your  
computer to  
In addition to images, you also can transfer  
screen shot images from your computer to  
the camera (Photo Transport*).  
camera memory  
Upload movie files  
to YouTube  
Movies files recorded using the “For  
YouTube” BEST SHOT scene can be easily  
uploaded to YouTube (YouTube Uploader  
for CASIO*).  
* Windows only  
The procedures you need to perform when using the camera with your computer and  
when using the software are different for Windows and the Macintosh.  
• Macintosh users should refer to “Using the Camera with a Macintosh” on page  
Using the Camera with a Computer  
 
80  
   
Using the Camera with a Windows Computer  
Install the required software in accordance with the version of Windows you are  
running and what you want to do.  
When you want Operating  
See  
page:  
Install this software:  
to do this:  
System Version  
Save images to  
a computer and  
view them there  
manually  
Windows 7,  
Windows Vista,  
Windows XP (SP3)  
Installation not required.  
Installation not required.  
• Windows Media Player, which is  
already installed on most  
computers, can be used for  
playback.  
Windows 7,  
Windows Vista,  
Windows XP (SP3)  
Play movies  
Photo Transport 1.0*  
• Download this software from the  
website below.  
http://www.casio-intl.com/support/  
• Download the user  
Windows 7,  
Windows Vista,  
Windows XP (SP3)  
Transfer images  
to the camera  
documentation for this software  
from the website below.  
http://www.exilim.com/manual/  
• System Requirements  
Memory: At least 64MB  
Hard Disk Drive Space: At least  
2MB  
YouTube Uploader for CASIO*  
• Download this software from the  
website below.  
http://www.casio-intl.com/support/  
• Download the user  
Windows 7,  
Windows Vista,  
Windows XP (SP3)  
Upload movie  
files to YouTube  
documentation for this software  
from the website below.  
http://www.exilim.com/manual/  
* Photo Transport and YouTube Uploader for CASIO will not run under 64-bit  
versions of Windows OS.  
Using the Camera with a Computer  
 
81  
 
. Precautions for Windows Users  
• The software requires Administrator privileges to run.  
• Operation on a self-made computer is not supported.  
• Operation may not be possible under certain computer environments.  
Viewing and Storing Images on a Computer  
You can connect the camera to your computer in order to view and store images  
(snapshot and movie files).  
Never use your computer to modify, delete, move, or rename any image files  
that are in the camera’s built-in memory or on its memory card.  
Doing so can cause problems with the camera’s image management data, which  
will make it impossible to play back images on the camera and can drastically alter  
remaining memory capacity. Whenever you want to modify, delete, move, or  
rename an image, do so only on images that are stored on your computer.  
IMPORTANT!  
• Never unplug the USB cable, or operate the camera while viewing or storing  
images. Doing so can cause data to become corrupted.  
NOTE  
• You also can use your computer’s card slot (if it has one) or a commercially  
available card reader to access image files directly from the camera’s memory  
card. For details, see the user documentation that comes with your computer.  
. To connect the camera to your computer and save files  
1. Turn off the camera and  
USB port  
then use the USB cable  
that comes with the  
camera to connect it to  
your computer.  
• For details about connecting  
to the camera and  
precautions when  
USB cable  
(included with camera)  
2. Turn on the camera.  
• The first time you connect the camera to your computer with the USB cable, an  
error message may appear on your computer. If this happens, disconnect and  
then reconnect the USB cable.  
• Charging continues even if the camera is turned on.  
3. Windows 7, Windows Vista users: Click “Start” and then “Computer”.  
Windows XP users: Click “Start” and then “My Computer”.  
Using the Camera with a Computer  
 
82  
 
4. Double-click “Removable Disk”.  
• Your computer recognizes the memory card loaded in the camera (or built-in  
memory if there is no card) as a removable disk.  
5. Right-click the “DCIM” folder.  
6. On the shortcut menu that appears, click “Copy”.  
7. Windows 7, Windows Vista users: Click “Start” and then “Documents”.  
Windows XP users: Click “Start” and then “My Documents”.  
• If you already have a “DCIM” folder in “Documents” (Windows 7, Windows  
Vista) or “My Documents” (Windows XP), the next step will overwrite it. If you  
want to keep the existing “DCIM” folder, you need to change its name or move  
it to a different location before performing the next step.  
8. Windows 7 users: On the “Documents” “Organize” menu, select  
“Paste”.  
Windows Vista users: On the “Documents” “Edit” menu, select  
“Paste”.  
Windows XP users: On the “My Documents” “Edit” menu, select  
“Paste”.  
This will paste the “DCIM” folder (and all the image files it contains) into your  
“Documents” (Windows 7, Windows Vista) or “My Documents” (Windows XP)  
folder. You now have a copy of the files that are in camera memory on your  
computer.  
9. After you finish copying images, disconnect the camera from the  
computer.  
On the camera, press [ON/OFF] (Power) to turn off the camera. After checking to  
make sure that the back lamp is unlit or lit red, disconnect the USB cable.  
Using the Camera with a Computer  
 
83  
. To view images you copied to your computer  
1. Double-click the copied “DCIM” folder to open it.  
2. Double-click the folder that contains the images you want to view.  
3. Double-click the image file you want to view.  
• For information about file names, see “Memory Folder Structure” on page 91.  
• An image that was rotated on the camera will be displayed on your computer  
screen in its original (unrotated) orientation.  
Playing Movies  
Windows Media Player, which is already installed on most computers, can be used  
for movie playback. To play back a movie, first copy the movie to your computer and  
then double-click the movie file.  
. Minimum Computer System Requirements for Movie Playback  
The minimum system requirements described below are necessary to play back  
movies recorded with this camera on a computer.  
Operating System : Windows 7, Windows Vista, Windows XP (SP3)  
CPU  
: Image Quality “HD”:  
Pentium 4 3.2 GHz or higher  
Image Quality “STD”:  
Pentium M 1.0 GHz or higher  
Pentium 4 2.0 GHz or higher  
Required Software: Windows Media Player, DirectX 9.0c or higher  
• The above are recommended system environments. Configuring one of these  
environments does not guarantee proper operation.  
• Certain settings and other installed software may interfere with proper playback of  
movies.  
Using the Camera with a Computer  
 
84  
 
. Movie Playback Precautions  
• Be sure to move the movie data to the hard disk of your computer before trying to  
play it. Proper movie playback may not be possible for data accessed over a  
network, from a memory card, etc.  
• Proper movie playback may not be possible on some computers. If you experience  
problems, try the following.  
– Try recording movies with a quality setting of “STD”.  
– Try upgrading Windows Media Player to the latest version.  
– Quit any other applications you have running, and stop resident applications.  
Even if proper playback is not possible on the computer, you can use an optionally  
available AV cable (EMC-7A) to connect to the video input terminal of a TV or  
computer and play back movies that way.  
Using the Camera with a Macintosh  
Install the required software in accordance with what version of the Macintosh OS  
you are running and what you want to do.  
Operating  
System  
Version  
When you want to do  
this:  
See  
page:  
Install this software:  
Save images to your  
Macintosh and view  
them there manually  
OS X  
OS X  
OS X  
Installation not required.  
Save images to your  
Macintosh  
automatically/Manage  
images  
Use iPhoto, which comes bundled  
with some Macintosh products.  
You can playback with QuickTime,  
which comes bundled with your  
operating system.  
Play movies  
Using the Camera with a Computer  
 
85  
 
Connecting the Camera to Your Computer and Saving Files  
Never use your computer to modify, delete, move, or rename any image files  
that are in the camera’s built-in memory or on its memory card.  
Doing so can cause problems with the camera’s image management data, which  
will make it impossible to play back images on the camera and can drastically alter  
remaining memory capacity. Whenever you want to modify, delete, move, or  
rename an image, do so only on images that are stored on your computer.  
IMPORTANT!  
• Never unplug the USB cable, or operate the camera while viewing or storing  
images. Doing so can cause data to become corrupted.  
• The camera does not support operation with Mac OS X 10.0. Operation is  
supported with Mac OS 10.1, 10.2, 10.3, 10.4, 10.5, 10.6, and 10.7 (using the OS  
standard USB driver) only.  
NOTE  
• You also can use your computer’s card slot (if it has one) or a commercially  
available card reader to access image files directly from the camera’s memory  
card. For details, see the user documentation that comes with your computer.  
. To connect the camera to your computer and save files  
1. Turn off the camera and  
USB port  
then use the USB cable  
that comes with the  
camera to connect it to  
your Macintosh.  
• For details about connecting  
to the camera and  
precautions when  
USB cable  
(included with camera)  
2. Turn on the camera.  
The camera’s back lamp will light green or amber at this time. In this mode, your  
Macintosh recognizes the memory card loaded in the camera (or the camera’s  
built-in memory if it does not have a memory card loaded) as a drive. The  
appearance of the drive icon depends on the Mac OS version you are using.  
• The first time you connect the camera to your Macintosh with the USB cable,  
an error message may appear on your computer. If this happens, disconnect  
and then reconnect the USB cable.  
• Charging continues even if the camera is turned on.  
3. Double-click the camera’s drive icon.  
Using the Camera with a Computer  
 
86  
 
4. Drag the “DCIM” folder to the folder to which you want to copy it.  
5. After the copy operation is complete, drag the drive icon to Trash.  
6. On the camera, press [ON/OFF] (Power) to turn off the camera. After  
checking to make sure that the back lamp is unlit or lit red, disconnect  
the USB cable.  
. To view copied images  
1. Double-click the camera’s drive icon.  
2. Double-click the “DCIM” folder to open it.  
3. Double-click the folder that contains the images you want to view.  
4. Double-click the image file you want to view.  
• For information about file names, see “Memory Folder Structure” on page 91.  
• An image that was rotated on the camera will be displayed on your Macintosh  
screen in its original (unrotated) orientation.  
Playing a Movie  
You can use QuickTime, which comes bundled with your operating system, to play  
back movies on a Macintosh. To play back a movie, first copy it to your Macintosh  
and then double-click the movie file.  
. Minimum Computer System Requirements for Movie Playback  
The minimum system requirements described below are necessary to play back  
movies recorded with this camera on a computer.  
Operating System : Mac OS X 10.3.9 or higher  
Required Software: QuickTime 7 or higher  
• The above are recommended system environments. Configuring one of these  
environments does not guarantee proper operation.  
• Certain settings and other installed software may interfere with proper playback of  
movies.  
Using the Camera with a Computer  
 
87  
 
. Movie Playback Precautions  
Proper movie playback may not be possible on some Macintosh models. If you  
experience problems, try the following.  
– Change the movie image quality setting to “STD”.  
– Upgrade to the latest version of QuickTime.  
– Shut down other applications that are running.  
Even if proper playback is not possible on your Macintosh, you can use an optionally  
available AV cable (EMC-7A) to connect to the video input terminal of a TV or  
Macintosh and play back movies that way.  
IMPORTANT!  
• Be sure to move the movie data to the hard disk of your Macintosh before trying to  
play it. Proper movie playback may not be possible for data accessed over a  
network, from a memory card, etc.  
Using an Eye-Fi Wireless SD Memory Card to Transfer Images  
(Eye-Fi)  
Shooting with an Eye-Fi wireless SD memory card loaded in the camera makes it  
possible to transfer image data automatically to a computer via wireless LAN.  
1. Configure LAN access point, transfer destination and other settings for  
the Eye-Fi card in accordance with the instructions that come with the  
Eye-Fi card.  
2. After configuring settings, load the Eye-Fi card into the camera and  
record.  
Images you record are sent by wireless LAN to your computer, etc.  
• For full details, see the user documentation that comes with the Eye-Fi card.  
• Before formatting a new Eye-Fi card to use it for the first time, copy the Eye-Fi  
Manager install files to your computer. Do this before formatting the card.  
Using the Camera with a Computer  
 
88  
   
IMPORTANT!  
• Recorded images are transferred over wireless LAN. Do not use the Eye-Fi card or  
turn off Eye-Fi card communication (page 93) when on an aircraft or in any other  
location where use of wireless communication is limited or prohibited.  
• Loading an Eye-Fi card will cause the Eye-Fi indicator  
to  
appear on the monitor screen. Its transparent or not transparent  
appearance indicates the communication status as shown below.  
Access point cannot be found or no  
Transparent  
transferable image data exists.  
Not transparent  
Flashing  
Image transfer in progress  
Searching for access points  
• A communication icon  
transfer is in progress.  
will appear on the monitor screen while image data  
• The camera’s Auto Power Off (page 98) function is disabled while image data  
transfer is in progress.  
• A confirmation message will appear on the monitor screen if you try to turn off the  
camera while image data transfer is in progress. Follow the instructions in the  
messages (page 120).  
• Transfer of a large number of images can take some time to complete.  
• Depending on the type of Eye-Fi card you are using and its settings, images on the  
Eye-Fi card may be deleted following image data transfer.  
• When recording a movie to an Eye-Fi card, it can take too much time to record  
data, which can result in breaks in the image and/or audio.  
• Proper Eye-Fi card data communication may not be possible due to camera  
settings, battery level, or operating conditions.  
Using the Camera with a Computer  
 
89  
Files and Folders  
The camera creates a file and saves it each time you shoot a snapshot, record a  
movie, or perform any other operation that stores data. Files are grouped by storing  
them in folders. Each file and folder has its own unique name.  
• For details about how folders are organized in memory, see “Memory Folder  
Name and Maximum Number Allowed  
Example  
File  
Each folder can contain up to 9999 files named 26th file name:  
CIMG0001 through CIMG9999. The extension  
CIMG0026.JPG  
on the file name depends on the file type.  
Extension  
Serial number (4 digits)  
Folders  
Folders are named from 100CASIO to  
100th folder name:  
999CASIO.  
100CASIO  
There can be up to 900 folders in memory.  
• The BEST SHOT (page 46) includes a sample  
scene that optimizes settings for auction site  
images. Depending on your camera model,  
the sample scene is named either “For eBay”  
or “Auction”.  
Serial number (3 digits)  
– Images recorded with the eBay scene are  
stored in a folder named “100_EBAY”.  
– Images recorded with the Auction scene are  
stored in a folder named “100_AUCT”.  
• BEST SHOT also has a scene named “For  
YouTube” that optimizes movie settings for  
recording movies for upload to YouTube.  
Images recorded with the YouTube scene are  
stored in a folder named “100YOUTB”.  
• You can view folder and file names on your computer. For details about how file  
names are displayed on the camera’s monitor screen, see page 10.  
• The total number of folders and files allowed depends on the image size and  
quality, and capacity of the memory card being used for storage.  
Using the Camera with a Computer  
 
90  
   
Memory Card Data  
The camera stores images you shoot in accordance with the Design Rule for Camera  
File System (DCF).  
. About DCF  
The following operations are supported for DCF-compliant images. Note, however,  
that CASIO makes no performance guarantees concerning these operations.  
• Transferring this camera’s DCF-compliant images to another manufacturer’s  
camera and view them.  
• Printing this camera’s DCF-compliant images on another manufacturer’s printer.  
• Transferring another camera’s DCF-compliant images to this camera and view  
them.  
. Memory Folder Structure  
DCIM Folder  
DCIM  
Recording Folder  
Image File  
Movie File  
Audio File  
Audio Snapshot Image File  
Audio Snapshot Audio File  
*
100CASIO  
CIMG0001.JPG  
CIMG0002.AVI  
CIMG0003.WAV  
CIMG0004.JPG  
CIMG0004.WAV  
*
Recording Folder  
Recording Folder  
101CASIO  
102CASIO  
*
DPOF File Folder  
DPOF File  
MISC  
AUTPRINT.MRK  
* Other folders are created when the following BEST SHOT scenes are used for  
recording: “For eBay” or “Auction” (scene name depends on camera model), or  
“For YouTube”. The following shows the name of the folder created for each scene.  
• eBay scene: 100_EBAY  
• Auction scene: 100_AUCT  
• YouTube scene: 100YOUTB  
Using the Camera with a Computer  
 
91  
     
. Supported Image Files  
• Image files shot with this camera  
• DCF-compliant image files  
This camera may not be able to display an image, even if it is DCF-compliant. When  
displaying an image recorded on another camera, it may take a long time for the  
image to appear on this camera’s monitor screen.  
. Built-in Memory and Memory Card Data Handling Precautions  
• Whenever copying memory contents to your computer, you should copy the DCIM  
folder and all of its contents. A good way to keep track of multiple DCIM copies of  
the DCIM folders is to change its name to a date or something similar after you  
copy it to your computer. If you later decided to return the folder to the camera,  
however, be sure to change its name back to DCIM. The camera is designed to  
recognize only a root file with the name DCIM. Note the camera also will not be  
able to recognize the folders inside the DCIM folder unless they have the names  
they originally had when you copied them from the camera to your computer.  
• Folders and files must be stored in accordance with the “Memory Folder Structure”  
shown on page 91 in order for the camera to be able to recognize them correctly.  
Using the Camera with a Computer  
 
92  
Other Settings (Set Up)  
This section explains menu items that you can use to configure settings and perform  
other operations in both the REC mode and PLAY mode.  
See the following for more information.  
– REC Menu (page 50)  
– PLAY Menu (page 69)  
Turning off Eye-Fi Card Communication (Eye-Fi)  
Procedure  
[SET] * MENU * “Set Up” Tab * Eye-Fi  
Select “Off” to disable Eye-Fi card communication (page 88).  
Configuring Camera Sound Settings (Sounds)  
Procedure  
[SET] * MENU * “Set Up” Tab * Sounds  
Startup  
Specifies the startup sound.  
Sound 1 - 5: Built-in sounds (1 through 5)  
Off: Sound off  
Half Shutter  
Shutter  
Operation  
Specifies the sound volume. This setting is also used as the  
= Operation  
audio level during video output (page 67).  
Specifies the volume of movie and Audio Snapshot audio  
= Play  
output. This setting is also used as the audio level during  
video output (page 67).  
• Setting a volume level of 0 mutes output.  
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)  
93  
     
Configuring a Startup Image (Startup)  
Procedure  
[SET] * MENU * “Set Up” Tab * Startup  
Display the image you want to use as your startup image and then select “On”.  
• The startup image does not appear when you turn on the camera by pressing  
[p] (PLAY).  
• You can specify a snapshot you recorded as the startup image, or you can use the  
special startup image provided in the camera’s built-in memory.  
• If you select an audio snapshot as the startup image, the audio will not play at  
startup.  
• Formatting built-in memory (page 100) will delete the current startup image setting.  
Specifying the File Name Serial Number Generation Rule  
(File No.)  
Procedure  
[SET] * MENU * “Set Up” Tab * File No.  
Use the following procedure to specify the rule that governs generation of the serial  
number used in file names (page 90).  
Tells the camera to remember the last used file number. A new file will  
be named using the next sequential number, even if files are deleted or  
if a blank memory card is loaded. If a memory card is loaded and that  
Continue card already has files stored on it and the largest sequential number in  
the existing file names is greater than the largest sequential number  
remembered by the camera, numbering of new files will start from the  
largest sequential number in the existing file names plus 1.  
Restarts the serial number from 0001 whenever all files are deleted or  
when the memory card is replaced with a blank one. If a memory card  
Reset  
is loaded and that card already has files stored on it, numbering of new  
files will start from the largest sequential number in the existing file  
names number plus 1.  
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)  
94  
   
Configuring World Time Settings (World Time)  
Procedure  
[SET] * MENU * “Set Up” Tab * World Time  
You can use the World Time screen to view the current time in a zone that is different  
from your Home City when you go on a trip, etc. World Time displays the current time  
in 162 cities in 32 time zones around the globe.  
1. Use [8] and [2] to select “Destination” and then press [6].  
• To change the geographic area and city for the time where you normally use  
the camera, select “Home”.  
2. Use [8] and [2] to select “City” and then press [6].  
• To change the “Destination” setting to summer time, use [8] and [2] to select  
“DST” and then select “On”. Summer time is used in some geographical areas  
to advance the current time setting by one hour during the summer months.  
3. Use [8], [2], [4], and [6] to select the geographic area you want and  
then press [SET].  
4. Use [8] and [2] to select the city you want and then press [SET].  
5. Press [SET].  
IMPORTANT!  
• Before configuring World Time settings, make sure that the Home City setting is  
the place where you live or normally use the camera. If it isn’t, select “Home” on the  
screen in step 1 and configure the Home City, date, and time settings as required  
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)  
95  
 
Time Stamping Snapshots (Timestamp)  
Procedure  
[SET] * MENU * “Set Up” Tab * Timestamp  
You can configure the camera to stamp the recording date only, or date and time in  
the lower right corner of each snapshot.  
• Once date and time information is stamped into a snapshot, it cannot be edited or  
deleted.  
Example: July, 10, 2015, 1:25 p.m.  
Date  
2015/7/10  
Date&Time  
Off  
2015/7/10 1:25pm  
No stamping of date and/or time  
• Even if you do not stamp the date and/or time with Timestamp, you can do so later  
using the DPOF function or some printing application (page 79).  
• Digital zoom is disabled while time stamping is turned on.  
• Time stamping is disabled when certain BEST SHOT scenes are being used.  
Setting the Camera’s Clock (Adjust)  
Procedure  
[SET] * MENU * “Set Up” Tab * Adjust  
[8] [2]  
Change the setting at the cursor location  
Move the cursor between settings  
[4] [6]  
[0] (Movie)  
Toggles between 12-hour and 24-hour format  
When the date and time settings are what you want, press [SET] to apply them.  
• You can specify a date from 2001 to 2049.  
• Be sure to select your Home City (page 95) before setting the time and date. If you  
set the time and date while the wrong city is selected for your Home City, the times  
and dates of all of the World Time cities (page 95) will be wrong.  
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)  
96  
       
Specifying the Date Style (Date Style)  
Procedure  
[SET] * MENU * “Set Up” Tab * Date Style  
You can select from among three different styles for the date.  
Example: July, 10, 2015  
YY/MM/DD  
DD/MM/YY  
MM/DD/YY  
15/7/10  
10/7/15  
7/10/15  
Specifying the Display Language (Language)  
Procedure  
[SET] * MENU * “Set Up” Tab * Language  
. Specify the display language you want.  
1
Select the tab on the right.  
Select “Language”.  
Select the language you want.  
1
2
23  
3
• Camera models sold in certain geographic areas  
may not support display language selection.  
Configuring Sleep State Settings (Sleep)  
Procedure  
[SET] * MENU * “Set Up” Tab * Sleep  
This feature turns off the monitor screen and lights the back lamp (green) whenever  
no camera operation is performed for a preset period of time. Press any button to turn  
the monitor screen back on.  
Trigger Time Settings: 30 sec, 1 min, 2 min, Off (Sleep is disabled while “Off” is  
selected.)  
• Sleep is disabled under any of the following conditions.  
– In the PLAY mode  
– While the camera is connected to a computer or other device  
– During O Tracking”  
– During Voice Recording playback or recording  
– During movie recording and playback  
• When both sleep and Auto Power Off are turned on, Auto Power Off takes priority.  
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)  
97  
           
Configuring Auto Power Settings (Auto Power Off)  
Procedure  
[SET] * MENU * “Set Up” Tab * Auto Power Off  
Auto Power Off turns off the camera whenever no camera operation is performed for  
a preset amount of time.  
Trigger Time Settings: 1 min, 2 min, 5 min (The trigger time is always 5 minutes in the  
PLAY mode.)  
• Auto Power Off is disabled under any of the following conditions.  
– While the camera is connected to a computer or other device  
– During a slideshow  
– During O Tracking”  
– During Voice Recording playback or recording  
– During movie recording and playback  
Configuring [r] Setting (REC)  
Procedure  
[SET] * MENU * “Set Up” Tab * REC  
Power On  
Camera turns on whenever [r] (REC) is pressed.  
Power On/Off  
Camera turns on or off whenever [r] (REC) is pressed.  
Camera does not turn on or off whenever [r] (REC) is  
pressed.  
Disable  
• With “Power On/Off”, the camera turns off when you press [r] (REC) in the REC  
mode.  
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)  
98  
       
Disabling File Deletion (Ü Disabled)  
Procedure  
[SET] * MENU * “Set Up” Tab * Ü Disabled  
The camera will not start the image delete operation when you press [ ] (Delete)  
while “Ü Disabled” is turned on.  
You can protect against accidental deletion of images by selecting “On” for  
Ü Disabled”.  
• Performing a format operation (page 100) will cause all images to be deleted, even  
if file deletion is disabled (“On” selected for “Ü Disabled”) for some images.  
Selecting the Screen Aspect Ratio and Video Output System  
(Video Out)  
Procedure  
[SET] * MENU * “Set Up” Tab * Video Out  
You can use the procedure in this section to select either NTSC or PAL as the video  
output system. You can also specify an aspect ratio of 4:3 or 16:9.  
NTSC  
PAL  
Video system used in Japan, the U.S., and other countries  
Video system used in Europe and other areas  
4:3  
TV screen aspect ratio of 4:3  
Wide screen aspect ratio  
16:9  
• Select the aspect ratio (4:3 or 16:9) that matches the type of TV you plan to use.  
Images will not display correctly if you select the wrong aspect ratio.  
• Images will not display correctly unless the camera’s video signal output setting  
matches the video signal system of the TV or other video equipment.  
• Images cannot be displayed correctly on a TV or video equipment that is not NTSC  
or PAL.  
• An optionally available AV cable (EMC-7A) is required for video output.  
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)  
99  
     
Formatting Built-in Memory or a Memory Card (Format)  
Procedure  
[SET] * MENU * “Set Up” Tab * Format  
If a memory card is loaded in the camera, this operation will format the memory card.  
It will format built-in memory if no memory card is loaded.  
• The format operation will delete all contents on the memory card or in built-in  
memory. It cannot be undone. Make sure you do not need any data currently on  
the card or in built-in memory before you format it.  
• Formatting built-in memory will delete the following data.  
– Protected images  
– Startup screen  
• Formatting a memory card will delete the following data.  
– Protected images  
• Formatting will cause all images to be deleted, even if file deletion is disabled (“On”  
selected for “Ü Disabled” (page 99)) for some images.  
• Make sure the camera’s battery is sufficiently charged before starting a formatting  
operation. Formatting may not be performed correctly and the camera may stop  
operating normally if the camera powers down while formatting is in progress.  
• Never open the battery cover while formatting is in progress. Doing so can cause  
the camera to stop operating normally.  
Resetting the Camera to Factory Defaults (Reset)  
Procedure  
[SET] * MENU * “Set Up” Tab * Reset  
See page 113 for details about the camera’s factory default settings.  
The settings below are not reset.  
World Time settings, clock settings, date style, screen language, video output  
Download from Www.Somanuals.com. All Manuals Search And DOotwhenr lSoeattdin.gs (Set Up)  
100  
       
Appendix  
Safety Precautions  
WARNING  
*
This indication stipulates matters that have the risk of causing death or serious injury  
if the product is operated incorrectly while ignoring this indication.  
CAUTION  
*
This indication stipulates matters that have the risk of causing injury as well as  
matters for which there is the likelihood of occurrence of physical damage only if the  
product is operated incorrectly while ignoring this indication.  
Symbol Examples  
This circle with a line through it (-) means that the indicated action must not  
be performed. Indications within or nearby this symbol are specifically  
prohibited. (The example at left indicates that disassembly is prohibited.)  
!
The black dot (0) means that the indicated action must be performed.  
Indications within this symbol are actions that are specifically instructed to be  
performed. (The example at left indicates that the power plug must be  
unplugged from the electrical socket.)  
$
WARNING  
*
. Smoke, abnormal odor, overheating, and other abnormalities  
• Continued use of the camera while it is emitting smoke or strange odor,  
$
or while it is overheating creates the risk of fire and electric shock.  
Immediately perform the following steps whenever any of the above  
symptoms are present.  
1. Turn off the camera.  
2. If you are using the USB-AC adapter to power the camera, unplug the power  
plug from the wall outlet. Also, remove the battery from the camera, taking  
care to protect yourself against burn injury.  
3. Contact your retailer or nearest CASIO authorized service center.  
. Keep Away From Fire  
• Never expose the camera to fire, which can cause it to explode and  
-
creates the risk of fire and personal injury.  
. Avoid Use While In Motion  
• Never use the camera to record or play back images while operating an  
-
automobile or other vehicle, or while walking. Looking at the monitor  
while in motion creates the risk of serious accident.  
Appendix  
 
101  
   
WARNING  
*
. Flash and Other Light Emitting Functions  
• Never use light emitting functions in areas where there is the chance of  
flammable or explosive gas being present. Such conditions create the  
risk of fire and explosion.  
• Never fire the flash or use light emitting functions pointed in the direction  
of a person operating a motor vehicle. Doing so can interfere with the  
driver’s vision and create the risk of accident.  
#
-
. USB-AC Adapter and Power Cord  
• When using the USB-AC adapter in another country, do so in accordance with  
the instructions of the User’s Guide.  
• Misuse of USB-AC adapter creates the risk of fire and electric shock. Be sure to  
observe the following precautions.  
– Use only the specified USB-AC adapter.  
-
– Never use the USB-AC adapter with another device.  
– Use a power outlet that matches the power supply specified for the  
USB-AC adapter.  
– Never plug the power cord into a wall outlet that is shared by other devices, or  
into a shared extension cord.  
• Misuse of the USB-AC adapter or power cord can cause them to become  
damaged, creating the risk of fire and electric shock. Be sure to observe the  
following precautions.  
– Never place heavy objects on the USB-AC adapter or subject it to  
-
direct heat.  
– Do not modify the USB-AC adapter, allow it to become damaged, or  
forcibly bend it.  
– Do not twist or pull on the USB-AC adapter cord.  
– When in use, locate the cord where it will not be tripped over.  
• Never touch the power plug while your hands are wet. Doing so creates  
"
+
the risk of electric shock.  
• Should the power cord or power plug become damage, contact your  
retailer or nearest CASIO authorized service center.  
• Do not use the USB-AC adapter or power cord in areas where liquids*  
-
might spill on them. Liquids create the risk of fire and electric shock.  
* Liquids: Water, sports drinks, seawater, animal or pet urine, etc.  
• Do not place a flower vase or any other liquid container on top of the  
%
USB-AC adapter or power cord. Water creates the risk of fire and  
electric shock.  
• Do not touch the power cord or power plug during lightning storms.  
1
+
• Before going out, be sure to unplug the power cord from the power  
outlet and put in a place away from objects used by animals and pets.  
An animal or pet chewing on the power cord can cause it short, leading  
to the risk of fire.  
Appendix  
 
102  
WARNING  
*
. Water and Foreign Matter  
• Water, other liquids, or foreign matter (especially metal) getting inside  
the camera creates the risk of fire and electric shock. Immediately  
perform the following steps whenever any of the above symptoms are  
%
present. Particular care is required when using the camera where it is raining or  
snowing, near the ocean or other body of water, or in a bathroom.  
1. Turn off the camera.  
2. If you are using the USB-AC adapter to power the camera, unplug the power  
plug from the wall outlet. Also, remove the battery from the camera, taking  
care to protect yourself against burn injury.  
3. Contact your retailer or nearest CASIO authorized service center.  
. Disassembly and Modification  
• Never try to take the camera apart or modify it in any way. Doing so  
!
creates the risk of electric shock, burn injury, and other personal injury.  
Be sure to leave all internal inspection, maintenance, and repair up to  
your retailer or nearest CASIO authorized service center.  
. Dropping and Rough Treatment  
• Continued use of the camera after it is damaged by dropping or other  
-
rough treatment creates the risk of fire and electric shock. Immediately  
perform the following steps whenever any of the above symptoms are  
present.  
1. Turn off the camera.  
2. If you are using the USB-AC adapter to power the camera, unplug the power  
plug from the wall outlet. Also, remove the battery from the camera, taking  
care to protect yourself against burn injury.  
3. Contact your retailer or nearest CASIO authorized service center.  
Appendix  
 
103  
WARNING  
*
. Rechargeable Battery  
• To charge the battery, use only the method specifically described in this  
manual. Attempting to charge the battery by an unauthorized means  
creates the risk of battery overheating, fire, and explosion.  
• Do not expose or immerse the battery in fresh water or salt water. Doing  
so can damage the battery, and cause deterioration of its performance  
and loss of service life.  
• The battery is intended for use with a CASIO Digital Camera only. Use  
with any other device creates the risk of the battery damage, or  
deterioration of battery performance and service life.  
+
%
+
• Failure to observe any of the following precautions creates the risk of battery  
overheating, fire, and explosion.  
– Never use or leave the battery near open flame.  
-
– Do not expose the battery to heat or fire.  
– Make sure the battery is oriented correctly when charging it.  
– Never carry or store the battery together with items that can conduct electricity  
(necklaces, pencil lead, etc.).  
– Never disassemble the battery, pierce it with a needle, or expose it to strong  
impact (hit it with a hammer, step on it, etc.), and never apply solder to it.  
Never place the battery into a microwave oven, dehumidifier, high-pressure  
generating device, etc.  
• Should you ever notice leakage, strange odor, heat generation,  
+
discoloration, deformation, or any other abnormal condition while using,  
charging, or storing a battery, immediately remove it from the camera  
and keep it away from open flame. Also, do not use the affected battery after the  
abnormal symptoms disappear.  
• Do not use or leave the battery under direct sunlight, in an automobile  
-
parked in the sun, or in any other area subject to high temperatures.  
Doing so can damage the battery, and cause deterioration of its  
performance and loss of service life. Also, these conditions can cause the  
battery to swell to the point that you may not be able to remove it.  
. Memory Cards  
• Memory cards are small and present a risk of accidentally being  
+
swallowed by infants and young children. Keep memory cards out of the  
reach of infants and young children. If a memory card is ever swallowed  
accidentally, contact a physician immediately.  
Appendix  
 
104  
CAUTION  
*
. USB-AC Adapter and Power Cord  
• Misuse of the USB-AC adapter or power cord creates the risk of fire and electric  
shock. Make sure you observe the following precautions.  
– Never cover the USB-AC adapter or power cord with a quilt, blanket,  
-
or other cover while it is in use, and do not use it near a heater. Doing  
so can interfere with heat radiation and cause the area around them  
to become hot.  
– When unplugging from the wall outlet, never pull on the power cord. Grasp the  
power plug and pull.  
– Do not use detergent when cleaning the power cord (especially the plug), the  
USB-AC adapter (especially the jack), or the USB cable (especially the plug).  
– Insert the power plug into the wall outlet as far as it will go.  
+
– Unplug the power plug from the wall outlet before leaving the camera  
unattended for long periods, such as when leaving on a trip, etc.  
– At least once a year, use a cloth or vacuum cleaner to clean any dust build up  
on the prongs of the power plug and in the area around them.  
. Rechargeable Battery  
• If battery charging does not end normally within the specified charging  
+
time, stop charging anyway and contact your local CASIO authorized  
service center. Continued charging creates the risk of battery  
overheating, fire, and explosion.  
• Battery fluid can damage your eyes. Should battery fluid get into your  
+
eyes accidentally, immediately rinse them with clean tap water and then  
consult a physician.  
• Be sure to read the user documentation that comes with the camera and  
+
+
special charger unit before using or charging the battery.  
• Store batteries in a location that cannot be reached by infants and young  
children. When using a battery where infants and young children are  
present, be on guard to ensure that they do not have the chance to  
remove the battery from the charger unit or camera.  
• Do not leave batteries near areas used by pets. A pet chewing on a  
-
battery can lead to accidents caused by the battery leaking, overheating,  
or exploding.  
• Should fluid from a battery accidentally get onto clothing or your skin,  
+
immediately rinse it off with clean tap water. Prolonged contact with  
battery fluid can cause skin irritation.  
Appendix  
 
105  
CAUTION  
*
. Connections  
• Never plug any devices that are not specified for use with this camera  
into connectors. Connecting a non-specified device creates the risk of  
fire and electric shock.  
-
-
. Unstable Locations  
• Never place the camera on an unstable surface, on a high shelf, etc.  
Doing so can cause the camera to fall, creating the risk of personal  
injury.  
. Locations To Be Avoided  
• Never leave the camera in any of the following types of locations. Doing so  
creates the risk of fire and electric shock.  
– Areas subject to large amounts of humidity or dust  
-
– Food preparation areas or other locations where oil smoke is present  
– Near heaters, on a heated carpet, in areas exposed to direct sunlight,  
in a closed vehicle parked in the sun, or other areas subject to very high  
temperatures  
. Monitor Screen  
• Do not apply strong pressure to the LCD panel surface or subject it to  
strong impact. Doing so can cause the display panel glass to crack and  
lead to personal injury.  
• Should the monitor screen ever become cracked, never touch any of the  
liquid inside the monitor screen. Doing so creates the risk of skin  
inflammation.  
-
1
• Should monitor screen liquid ever get into your mouth, immediately rinse  
your mouth out and contact your physician.  
+
+
• Should monitor screen liquid ever get into your eyes or onto your skin,  
immediately rinse with clean water for at least 15 minutes and contact  
your physician.  
. Backing Up Important Data  
• Always keep backup copies of important data in camera memory by  
transferring it to a computer or other storage device. Note that data can  
be deleted in the case of camera malfunction, repair, etc.  
+
Appendix  
 
106  
CAUTION  
*
. Memory Protection  
• Whenever replacing the battery, be sure to follow the correct procedure  
as described in the documentation that comes with the camera.  
Incorrectly replacing the battery can result in corruption or loss of data in  
camera memory.  
+
-
-
. Flash and Other Light Emitting Functions  
• Never fire the flash or use light emitting functions pointed in the direction  
of and too close to a person’s face. Doing so creates the risk of loss of  
eyesight. In the case of infants and young children in particular, keep the  
light source at least one meter away the eyes.  
. Transport  
• Never operate the camera inside of an aircraft or anywhere else where  
operation of such devices is restricted. Improper use creates the risk of  
serious accident.  
Appendix  
 
107  
Precautions During Use  
. Data Error Precautions  
Your digital camera is manufactured using precision digital components. Any of the  
following creates the risk of corruption of data in camera memory.  
– Removing the battery or memory card while the camera is performing some  
operation  
– Removing the battery or memory card while the back lamp is flashing green after  
turning off the camera  
– Disconnecting the USB cable while communication is in progress  
– Shooting with a battery that quickly goes low right after it is charged  
• Shooting with a battery that quickly goes low right after it is charged can also  
cause camera malfunction. Replace the battery with a new one immediately.  
– Other abnormal operations  
Any of the above conditions can cause an error message to appear on the monitor  
screen (page 120). Perform the action indicated by the message that appears.  
. Operating Environment  
• Operating Temperature Requirements: 0 to 40°C (32 to 104°F)  
• Operating Humidity: 10 to 85% (non condensation)  
• Do not place the camera in any of the following locations.  
– In an area exposed to direct sunlight, or large amounts of moisture, dust, or sand  
– Near heating or cooling devices, or in other areas subjected to extreme changes  
in temperature or humidity  
– Inside of a motor vehicle on a hot day, or in an area subjected to strong vibration  
. Condensation  
Sudden and extreme temperature changes, such as when the camera is moved from  
the outdoors on a cold winter day into a warm room, can cause water droplets called  
“condensation” to form on the interior and the exterior of the camera, which creates  
the risk of malfunction. To prevent condensation from forming seal the camera in a  
plastic bag before changing locations. Then leave the bag sealed to allow the air  
inside to naturally change to the same temperature as the air in the new location.  
After that, remove the camera from the bag and open the battery cover for a few  
hours.  
Appendix  
 
108  
 
. Lens  
• Never apply too much force when cleaning the surface of the lens. Doing so can  
scratch the lens surface and cause malfunction.  
• You may sometimes notice some distortion in certain types of images, such as a  
slight bend in lines that should be straight. This is due to the characteristics of  
lenses, and does not indicate malfunction of the camera.  
. Caring for your camera  
• Never touch the lens or flash window with your fingers. Finger smudges, dirt, and  
other foreign matter on the lens or flash window can interfere with proper operation  
of the camera. Use a blower or other means to keep the lens and flash window free  
of dirt and dust, and wipe gently with a soft, dry cloth.  
• To clean the camera, wipe it with a soft, dry cloth.  
. Old Rechargeable Battery Handling Precautions  
• Insulate the positive and negative terminals with tape, etc.  
• Do not peel the covering off of the battery.  
• Do not try to take the battery apart.  
. Discarding or Transferring Ownership of a Memory Card or the  
Camera  
The format and delete functions of the camera do not actually delete files from the  
memory card. The original data remains on the card. Note that responsibility for the  
data on a memory card lies with you. The following procedures are recommended  
whenever you discard a memory card or the camera, or if you transfer ownership to  
another party.  
• When discarding a memory card, either physically destroy the memory card or use  
commercially available data delete software to completely delete the data on the  
memory card.  
• When transferring ownership of a memory card to another party, use commercially  
available data deletion software to completely delete the data on it.  
• Use the format function (page 100) to completely delete the data in built-in memory  
before discarding or transferring ownership of the camera.  
. Other Precautions  
The camera becomes slightly warm during use. This is normal and does not indicate  
malfunction.  
Appendix  
 
109  
 
. Copyrights  
Except for your own personal enjoyment, unauthorized use of snapshots or movies of  
images whose rights belong to others, without the permission of the right holder, is  
forbidden by copyright laws. In some cases, shooting of public performances, shows,  
exhibitions, etc. may be restricted entirely, even if it is for your own personal  
enjoyment. Regardless of whether such files are purchased by you or obtained for  
free, posting them on a website, a file sharing site, or any other Internet site, or  
otherwise distributing them to third parties without the permission of the copyright  
holder is strictly prohibited by copyright laws and international treaties. For example,  
uploading or distributing on the Internet images of TV programs, live concerts, music  
videos, etc. that were photographed or recorded by you may infringe upon the rights  
of others. Note that CASIO COMPUTER CO., LTD. shall not be held liable for use of  
this product in any way that infringes on the copyrights of others or that violates  
copyright laws.  
The following terms, which are used in this manual, are registered trademarks or  
trademarks of their respective owners.  
Note that trademark and registered trademark ® are not used within the text of this  
manual.  
• SDXC Logo is a trademark of SD-3C, LLC.  
• Microsoft, Windows, Windows Media, Windows Vista, Windows 7, and DirectX are  
registered trademarks or trademarks of Microsoft Corporation in the United States  
and other countries.  
• Macintosh, Mac OS, QuickTime, and iPhoto are trademarks of Apple Inc.  
• YouTube and the YouTube logo are trademarks or registered trademarks of  
Google Inc.  
• Eye-Fi and the Eye-Fi logo are trademarks of Eye-Fi, Inc.  
• EXILIM, Photo Transport, and YouTube Uploader for CASIO are registered  
trademarks or trademarks of CASIO COMPUTER CO., LTD.  
• All other company or product names mentioned herein are registered trademarks  
or trademarks of their respective companies.  
Any and all unauthorized copying, distribution, and transfer for commercial purposes  
of the software provided by CASIO for this product are prohibited.  
YouTube Uploader for CASIO and the camera’s YouTube recording function are  
provided under license granted by YouTube, LLC. The presence of YouTube upload  
functionality in this product is not an endorsement or recommendation of the product  
by YouTube, LLC.  
Appendix  
 
110  
Power Supply  
Charging  
. If the camera’s back lamp starts flashing red...  
• Ambient temperature or the temperature of the battery may be either too high or  
too low. Disconnect the USB cable and wait until temperature is within the  
allowable charging range before trying again.  
• Battery contacts may be dirty. Wipe them with a dry cloth.  
• Try connecting to a different computer USB port. Depending on the setup of your  
computer, you may not be able to charge the camera’s battery over a USB  
connection.  
If problems continue to occur after you perform the above steps, it could mean that  
the battery is faulty. Contact your nearest CASIO authorized service center.  
Battery Precautions  
. Precautions during Use  
• Operation provided by a battery under cold conditions is always less than operation  
under normal temperatures. This is due to the characteristics of the battery, not the  
camera.  
• Charge the battery in an area where the temperature is within the range of 10°C to  
35°C (50°F to 95°F). Outside this temperature range charging can take longer than  
normal or even fail.  
• Do not tear or remove the battery outer label.  
• If a battery provides only very limited operation following a full charge, it probably  
means the battery has reached the end of its service life. Replace the battery with a  
new one.  
. Storage Precautions  
• Storing the battery for a long time while it is charged can cause deterioration of  
battery characteristics. If you do not plan to use a battery for some time, fully use  
up its charge before storing it.  
• Always remove the battery from the camera when you are not using it. A battery left  
in the camera can discharge and go dead, which will require some time to charge  
when you need to use the camera.  
• Store batteries in a cool, dry place (20°C (68°F) or lower).  
• To prevent over discharging of an unused battery, fully charge it, and then load it in  
the camera and fully use up the charge about once every six months.  
Appendix  
 
111  
       
Using the Camera in another Country  
. Precautions during Use  
• The bundled USB-AC adaptor is designed for operation with any power supply in  
the range of 100V to 240V AC, 50/60Hz. Note, however, that the shape of the  
power cord plug depends on each country or geographic area. Before taking the  
camera and USB-AC adaptor along on a trip, check with travel agent about the  
power supply requirements in your destination(s).  
• Do not connect the USB-AC adaptor to a power supply through a voltage converter  
or similar device. Doing so can lead to malfunction.  
. Extra Batteries  
• Taking along extra fully charged batteries (NP-80) is recommended while on a trip  
in order to avoid not being able to shoot images due to the battery going dead.  
Using a Memory Card  
See page 19 for information about supported memory cards and how to load a  
memory card.  
. Using a Memory Card  
• SD memory cards, SDHC memory cards, and SDXC  
memory cards have a write protect switch. Use the  
switch when you need to guard against accidentally  
deleting data. Note, however, if you write protect an SD  
memory card you must then turn write protection off  
whenever you want to record to it, format it, or delete  
any of its images.  
Write enabled  
Write disabled  
• If a memory card starts to behave abnormally during image playback, you can  
restore normal operation by reformatting it (page 100). However, it is  
recommended that you always take along multiple memory cards whenever using  
the camera far away from the home or office.  
• As you record data to and delete data from a memory card a number of times, it  
loses its ability to retain data. Because of this, periodic re-formatting of a memory  
card is recommended.  
• Electrostatic charge, electrical noise, and other phenomena can cause data to  
become corrupted or even lost. Make sure that you always back up important data  
on other media (CD-R, CD-RW, hard disk, etc.).  
Appendix  
 
112  
   
. Memory Card Handling Precautions  
• Certain types of memory cards can slow down processing speed. Whenever  
possible use an Ultra High-Speed Type memory card. Note, however, that not all  
operations can be guaranteed even if an Ultra High-Speed Type memory card is  
used. Certain movie quality settings can result in too much time being required to  
record data, which can result in breaks in the image and/or audio during playback.  
»
Y
If this happens, the  
and  
will flash on the monitor screen.  
Reset Initial Default Settings  
The tables in this section show the initial default settings on menus that appear in the  
REC mode and PLAY mode when you reset the camera (page 100).  
• A dash (–) indicates an item whose setting is not reset or an item for which there is  
no reset setting.  
IMPORTANT!  
• Depending on the recording mode, some of the items on the menu that appears  
may not be usable.  
. REC Mode  
“REC” Tab  
Focus  
Auto Focus  
ß
Icon Help  
Memory  
On  
b
Focus Frame  
AF Area  
BEST SHOT:  
Off / Flash: On /  
Focus: Off /  
White Balance: Off /  
ISO: Off /  
AF Area: On /  
CS: Off /  
Self-timer: Off /  
MF Position: Off /  
Zoom Position: Off  
I Multi  
Face Detection On  
CS  
Off  
Off  
Off  
Off  
Anti Shake  
L/R Key  
Grid  
“Quality” Tab  
T
Quality  
ISO  
Auto  
Off  
Normal  
0.0  
(Snapshots)  
Color Filter  
EV Shift  
White Balance Auto  
Appendix  
 
113  
   
“Set Up” Tab  
Eye-Fi  
On  
Date Style  
Language  
Sleep  
Startup: Sound 1 /  
Half Shutter:  
Sound 1 /  
1 min  
Auto Power  
Off  
Shutter: Sound 1 /  
Operation: Sound 1 /  
=Operation:  
2 min  
Sounds  
REC  
Off  
Off  
...////  
/
Ü Disabled  
Video Out  
Format  
=Play: ...////  
Startup  
Off  
File No.  
Continue  
Reset  
World Time  
Timestamp  
Adjust  
Off  
. PLAY Mode  
“PLAY” Tab  
DPOF Printing  
Protect  
Trimming  
Dubbing  
Copy  
Resize  
“Set Up” Tab  
• The contents of the “Set Up” tab are the same in the REC mode and PLAY mode.  
Appendix  
 
114  
When things don’t go right...  
Troubleshooting  
Problem  
Possible Cause and Recommended Action  
Power Supply  
Power does not  
turn on.  
1)The battery may not be loaded correctly (page 13).  
2)The battery may be dead. Charge the battery (page 14). If the  
battery goes dead soon after being charged, it means the  
battery has reached the end of its life and needs to be  
replaced. Purchase a separately available CASIO NP-80  
rechargeable lithium ion battery.  
The camera  
suddenly powers  
down.  
1)Auto Power Off may have activated (page 98). Turn power  
back on.  
2)The battery may be dead. Charge the battery (page 14).  
3)The camera’s protection function may have activated  
because camera temperature is too high. Turn off the camera  
and wait until it cools down before trying to use it again.  
Power will not turn Remove the battery from the camera and then reload it.  
off. Nothing  
happens when a  
button is pressed.  
Image Recording  
r
] (REC) to enter  
Image is not  
1)If the camera is in the PLAY mode, press [  
the REC mode.  
recorded when the  
shutter button is  
pressed.  
2)If the flash is charging, wait until the charge operation  
finishes.  
3)If the message “Memory Full” appears, transfer images to  
your computer, delete images you no longer need, or use a  
different memory card.  
Auto Focus does  
1)If the lens is dirty, clean it off.  
not focus properly. 2)The subject may not be in the center of the focus frame when  
you compose the image.  
3)The subject you are shooting may not be a type that is  
compatible with Auto Focus (page 30). Use manual focus  
(page 52).  
4)You may be moving the camera when shooting. Try shooting  
with Anti Shake or use a tripod.  
5)You may be pressing the shutter button all the way without  
waiting for Auto Focus. Half-press the shutter button and  
allow enough time for Auto Focus to focus.  
Appendix  
 
115  
   
Problem  
Possible Cause and Recommended Action  
The subject is out  
of focus in the  
The image may not be focused properly. When composing the  
image, make sure the subject is located inside the focus frame.  
recorded image.  
?
The flash does not 1)If  
(Flash Off) is selected as the flash mode, change to  
fire.  
another mode (page 35).  
2)If the battery is dead, charge it (page 14).  
?
3)If a BEST SHOT scene that uses  
(Flash Off) is selected,  
change to a different flash mode (page 35) or select a  
different BEST SHOT scene (page 46).  
The red ? (Flash The flash unit may be malfunctioning. Contact a CASIO  
Off) icon is  
displayed on the  
authorized service center or your original retailer. Note that  
though the flash will not fire, you still can use the camera for  
monitor screen and non-flash shots.  
the flash does not  
fire.  
Camera powers  
down during Self-  
timer countdown.  
The battery may be dead. Charge the battery (page 14).  
The monitor screen 1)You may be using Manual Focus and have not focused the  
image is out of  
focus.  
image. Focus the image (page 53).  
´
2)You may be using  
(Macro) for scenery or portraits. Use  
Auto Focus for scenery and portrait shots (page 52).  
3)You may be trying to use Auto Focus or ) (Infinity) when  
´
shooting a close-up shot. Use the  
(page 52).  
(Macro) for close ups  
There is a vertical  
line in the monitor  
screen image.  
Shooting a very brightly lit subject can cause a vertical band to  
appear in the monitor screen image. This is a CCD  
phenomenon known as “vertical smear”, and does not indicate  
malfunction of the camera. Note that vertical smear is not  
recorded with the image in the case of a snapshot, but it is  
recorded in the case of a movie.  
There is digital  
noise in images.  
1)Sensitivity may have been increased automatically for a dark  
subject, which increases the chance of digital noise. Use a  
light or some other means to illuminate the subject.  
?
2)You may be attempting to shoot in a dark location with  
(Flash Off) selected, which can increase digital noise and  
make images appear coarse. In this case, turn on flash (page  
35) or use lights for illumination.  
3)Shooting with a high ISO sensitivity setting or with the  
Lighting feature can cause an increase in digital noise. Use a  
light or some other means to illuminate the subject.  
Appendix  
 
116  
Problem  
Possible Cause and Recommended Action  
A recorded image  
was not saved.  
1)Camera power may have been turned off before the save  
operation was complete, which will result in the image not  
being saved. If the battery indicator shows  
battery as soon as possible (page 17).  
, charge the  
2)You may have removed the memory card from the camera  
before the save operation was complete, which will result in  
the image not being saved. Do not remove the memory card  
before the save operation is complete.  
Though available  
lighting is bright,  
Not enough light is reaching the subjects. Change the flash  
<
mode setting to  
(Flash On) for daylight synchro flash (page  
the faces of people 35), or adjust EV shift to the + side (page 61).  
in the image are  
dark.  
Night shots come  
out bad.  
Use the following BEST SHOT scenes (page 46) when shooting  
at night.  
• Night Scene (for shooting night scenery only)  
• Night Scene Portrait (for shooting people against night  
scenery)  
Subjects are too  
Sunlight reflected by water, sand, or snow, can cause  
<
dark when shooting underexposure of images. Change the flash mode setting to  
images in a  
seashore or ski  
area.  
(Flash On) for daylight synchro flash (page 35), or adjust EV  
shift to the + side (page 61).  
Digital zoom  
(including HD  
Time stamping may be turned on, which will cause digital zoom  
to be disabled. Turn off time stamping (page 96).  
zoom) does not  
work. The zoom  
bar indicates zoom  
only up to a zoom  
factor of 5.0.  
The image is out of 1)Focusing may not be possible because the subject is outside  
focus during movie  
recording.  
the focus range. Shoot within the allowable range.  
2)The lens may be dirty. Clean the lens (page 109).  
Appendix  
 
117  
Problem  
Playback  
Possible Cause and Recommended Action  
The color of the  
playback image is  
Sunlight or light from another source may be shining directly  
into the lens when you are shooting. Position the camera so  
different from what sunlight does not shine directly into the lens.  
appears on the  
monitor screen  
when shooting.  
Images are not  
displayed.  
This camera cannot display non-DCF images recorded onto a  
memory card using another digital camera.  
Images cannot be  
edited (with  
Note that you cannot edit the following types of snapshots.  
• Movies  
resizing, trimming,  
rotation).  
• Snapshots recorded with another camera  
File Deletion  
A file cannot be  
deleted.  
1)The file may be protected. Unprotect the file (page 73).  
2)“Ü Disabled” setting may be “On”. Change the setting to  
“Off” (page 99).  
Other  
The wrong date  
and time are  
The date and time setting is off. Set the correct date and time  
(page 96).  
displayed, or the  
wrong date and  
time are being  
stored along with  
image data.  
The messages on  
the display are in  
the wrong  
The wrong display language is selected. Change the display  
language setting (page 97).  
language.  
Images cannot be  
transferred over a  
USB connection.  
1)The USB cable may not be connected securely. Check all  
connections.  
2)If the camera is not turned on, turn it on.  
3)Your computer may not be able to recognize the camera if  
you connect via a USB hub. Always connect directly to the  
computer’s USB port.  
Appendix  
 
118  
Problem  
Possible Cause and Recommended Action  
Languageselection 1)You did not configure initial settings after purchasing the  
screen appears  
when the camera is  
turned on.  
camera or the camera may have been left with a dead  
battery. Check the camera setup (pages 18, 97).  
2)There may be a problem with the camera’s memory data. If  
this is the case, perform the reset operation to initialize the  
camera’s setup (page 100). After that, configure each setting.  
If the language selection screen does not re-appear when you  
turn the camera on, it means that the camera’s memory  
management data has been restored.  
If the same message appears after you turn power back on,  
contact your retailer or a CASIO authorized service center.  
There are various  
indicators and  
values on the  
The monitor screen shows indicators and other information  
about shooting conditions and the image you are recording. You  
can use [8] (DISP) to select what information you want to  
include on the display (page 11).  
monitor screen.  
The time and date Load the camera’s battery and reconfigure the time and date  
settings configured settings (page 18). Do not remove the battery from the camera  
the first time after  
purchasing the  
for at least 24 hours after configuring time and date settings.  
After that, the settings will not be reset if you remove the  
camera are reset to battery.  
their factory  
• If the time and date are reset to their factory default settings  
defaults when  
remove the  
camera’s battery.  
when you remove the battery after it has been loaded for  
more than 24 hours, it could mean that the camera’s setting  
memory is defective. Contact your retailer or a CASIO  
authorized service center.  
Buttons are not  
responsive right  
With large capacity memory cards there is a delay after the  
power has been turned on before the buttons become  
after the power has responsive.  
been turned on.  
Appendix  
 
119  
Display Messages  
The camera’s protection function may have activated  
because camera temperature is too high. Turn off the  
camera and wait until it cools down before trying to use it  
again.  
ALERT  
Battery is low.  
Battery power is low.  
There is something wrong with the memory card. Turn off the  
camera, remove the memory card and then reload it into the  
camera. If this message re-appears when you turn the  
camera back on, format the memory card (page 100).  
Card ERROR  
IMPORTANT!  
• Formatting a memory card deletes all its files. Before  
formatting, try transferring recoverable files to a computer  
or some other storage device.  
File could not be  
saved because  
battery is low.  
Battery power is low, so an image file could not be saved.  
You are trying to record a file while there are already 9999  
files stored in the 999th folder. If you want to record more,  
delete files you no longer need (page 29).  
Folder cannot be  
created.  
Images are being  
transferred. Stop  
transfer and turn  
off power?  
You are attempting to turn off power while image data is  
being transferred using the Eye-Fi card (page 88).  
This message appears and the camera turns off whenever  
lens performs some unexpected operation. If the same  
message appears after you turn power back on, contact a  
CASIO authorized service center or your original retailer.  
LENS ERROR  
Memory is full with images you recorded and/or files saved  
by editing operations. Delete files you no longer need (page  
29).  
Memory Full  
Record Error  
Image compression could not be performed for some reason  
during image data storage. Shoot the image again.  
The lens came into contact with an obstruction while moving.  
The camera will turn off automatically when this message  
appears. Remove the obstruction and turn power back on  
again.  
RETRY POWER ON  
SYSTEM ERROR  
Your camera system is corrupted. Contact your retailer or a  
CASIO authorized service center.  
Appendix  
 
120  
   
The LOCK switch of the SD, SDHC, or SDXC  
memory card loaded in the camera is in the  
The card is locked. locked position. You cannot store images to  
or delete images from a memory card that is  
locked.  
LOCK  
There are no files. There are no files in built-in memory or on the memory card.  
This card is not  
formatted.  
The memory card loaded in the camera is not formatted.  
Format the memory card (page 100).  
This file cannot be The file you are trying to access is corrupted or is a type that  
played.  
cannot be displayed by this camera.  
This message will appear part way through an operation  
when you attempt to use a function that is not allowed in  
combination with another function.  
This function  
cannot be used.  
Appendix  
 
121  
Number of Snapshots/Movie Recording Time/  
Voice Recording Time  
Snapshot  
2
SD Memory Card  
Recording  
*
1
Image Size  
(Pixels)  
Approximate  
File Size  
Built-in Memory  
*
Quality  
Recording Capacity  
Capacity  
16M  
(4608 3456)  
Fine  
Normal  
Fine  
5.57MB  
3.71MB  
4.92MB  
3.28MB  
4.10MB  
2.75MB  
3.38MB  
2.27MB  
1.72MB  
1.22MB  
1.25MB  
820KB  
7
2791  
4191  
x
11  
8
3:2  
3160  
x
(4608 3072)  
Normal  
Fine  
12  
9
4740  
16:9  
(4608 2592)  
3792  
x
Normal  
Fine  
14  
12  
18  
23  
33  
32  
49  
141  
170  
5654  
10M  
(3648 2736)  
4600  
x
Normal  
Fine  
6849  
5M  
9040  
x
(2560 1920)  
Normal  
Fine  
12744  
12439  
18962  
53616  
64786  
3M  
x
(2048 1536)  
Normal  
Fine  
VGA  
(640 480)  
290KB  
x
Normal  
240KB  
Appendix  
 
122  
     
Movies  
Maximum  
Recording File Size of  
Time with  
Built-in  
Memory*  
Recording  
Capacity  
Continuous  
Recording  
Image  
Size/Pixels  
(Audio)  
1
Approximate Data Maximum  
1-minute  
Movie  
Rate (Frame Rate)  
File Size  
Time per  
SD Memory  
3
Movie  
*
2
Card*  
HD  
1280 720  
(Monaural) (30 frames/second)  
30.2 Megabits/  
second  
1 hour  
5 minutes  
23 seconds  
17 minutes  
9 seconds  
4
x
9 seconds  
*
226.3MB  
79.0MB  
4GB or  
29 minutes  
STD  
640 480  
(Monaural) (30 frames/second)  
10.6 Megabits/  
second  
3 hours  
6 minutes  
34 seconds  
x
28 seconds  
29 minutes  
Voice Recording  
1
Built-in Memory  
*
SD Memory  
Card  
2 Recording  
Continuous  
Recording Time  
per Recording*  
Maximum  
File Size  
File Format  
File Size  
Recording  
Capacity  
*
3
Capacity  
WAV  
IMA-ADPCM  
2 hours  
6 minutes  
796 hours  
53 minutes  
3 hours  
40 minutes  
5.5 KB/second  
4GB  
*1 Built-in memory capacity after formatting (Approx. 41.0MB)  
*2 When using a 16GB SDHC memory card (SanDisk Corporation). Number of image and  
recording time values depend on the memory card you are using.  
*3 The allowable recording time will be shorter if the capacity of the SD memory card you  
are using is smaller than the maximum size of one file.  
*4 The data transfer rate of built-in memory is not sufficient for HD movies. Whenever  
possible use an Ultra High-Speed Type memory card.  
• Snapshot, movie recording capacity, and voice recording capacity values are  
approximate and intended for reference only. Actual capacity depends on image  
contents.  
• File size and data rate values are approximate and intended for reference only. Actual  
values depend on the type of image being shot.  
• When using a memory card with a different capacity, calculate the number of images as a  
percentage of 16GB.  
• Each movie can be up to 29 minutes long. Movie recording stops automatically after  
29 minutes of recording.  
• The maximum size and of each file when shooting with the “For YouTube” scene is  
2048MB. The maximum recording time is 15 minutes.  
Appendix  
 
123  
   
Specifications  
File Format  
Snapshots:  
JPEG (Exif Version 2.3); DCF 2.0 standard; DPOF compliant  
Movies:  
Motion JPEG AVI, IMA-ADPCM audio (monaural)  
Audio (Voice Recording): WAV (monaural)  
Recording Media  
Built-in Memory (Image Storage Area: 41.0MB)  
SD/SDHC/SDXC  
Recorded Image Sizes Snapshot:  
16M (4608 3456), 3:2 (4608 3072), 16:9 (4608 2592),  
x
x
x
x
x
x
10M (3648 2736), 5M (2560 1920), 3M (2048 1536),  
x
VGA (640 480)  
Movies:  
x
x
HD (1280 720), STD (640 480)  
Effective Pixels  
Imaging Element  
16.10 Megapixels  
Size: 1/2.3-inch square pixel CCD  
Total Pixels: 16.44 Megapixels  
Lens/Focal Distance  
Zoom  
F3.2 (W) to 6.5 (T) f = 4.6 to 23.0 mm  
(equivalent to 26 to 130 mm in 35 mm format)  
5X optical zoom, 4X digital zoom (20X in combination with  
optical zoom)  
Up to 79.7X when HD Zoom and Digital zoom are used in  
combination (VGA size)  
Focusing  
Contrast Detection Auto Focus  
• Focus Modes:  
Auto Focus, Macro Focus, Infinity, Manual Focus  
• AF Area:  
Spot, Multi, Tracking  
9
9
) (Wide Angle)  
Approximate Focus  
(Snapshot)  
(From Lens Surface)  
Auto Focus: 10 cm to  
(3.9" to  
Macro Focus: 10 cm to 50 cm (3.9" to 19.7") (Wide Angle)  
9
Infinity:  
(Wide Angle)  
Manual: 10 cm to 9 (3.9" to 9) (Wide Angle)  
• Range is affected by optical zoom.  
Metering  
Multi-pattern (center weighted for some BS scenes) by imaging  
element  
Exposure Control  
Program AE  
Exposure  
–2.0 EV to +2.0 EV (in 1/3EV steps)  
Compensation  
Shutter  
CCD shutter, mechanical shutter  
Shutter Speed  
Snapshot (Auto): 1/2 to 1/2000 second  
Snapshot (Premium Auto): 1/8 to 1/2000 second  
Snapshot (Night Scene): 4 to 1/2000 second  
• May differ due to the camera setup.  
Aperture Value  
F3.2 (W) to F8.0 (W) (When used with ND filter)  
• Using optical zoom changes the aperture value.  
Appendix  
 
124  
   
White Balance  
Auto, Daylight, Overcast, Shade, Day White Fluorescent,  
Daylight Fluorescent, Tungsten, Manual WB  
Sensitivity (Standard  
Output Sensitivity)  
Snapshots:  
Auto, ISO 64, ISO 100, ISO 200, ISO 400, ISO 800,  
ISO 1600 equivalent  
Movies: Auto  
Flash Modes  
Flash Range  
Auto, Off, On, Red-eye reduction  
Wide Angle: 0.4 m to 2.5 m (1.3' to 8.2')  
(ISO Sensitivity: Auto) Telephoto: 0.8 m to 1.2 m (2.6' to 3.9')  
• Range is affected by optical zoom.  
Flash Charging Time  
Monitor Screen  
Approximately 5 seconds maximum  
2.7-inch TFT color LCD  
x
230,400 (960 240) dots  
External connection  
terminal  
USB port (Hi-Speed USB standard) /  
AV output terminal (NTSC/PAL)  
Microphone  
Monaural  
Speaker  
Monaural  
x
1
Power Requirements  
Rechargeable lithium ion battery (NP-80)  
Appendix  
 
125  
   
Approximate Battery Life  
All of the values provided below represent the approximate amount of time under  
normal temperature (23°C (73°F)) before the camera turns off. These values are not  
guaranteed. Low temperatures shorten battery life.  
Number of snapshots (Operating Time)*1  
Actual movie recording time (HD movie)*1  
180 shots  
50 minutes  
Approximate continuous movie recording time  
1 hour 20 minutes  
(HD movies)*1  
Continuous Voice Recording*2  
Continuous Playback*3  
3 hours 40 minutes  
3 hours 20 minutes  
• Battery: NP-80 (Rated Capacity: 700 mAh)  
• Recording Medium: 16GB SDHC memory card (SanDisk Corporation)  
*1 In accordance with CIPA (Camera and Imaging Products Association) standards  
*2 Approximate continuous recording time  
*3 Standard temperature (23°C (73°F)), one-image scroll approximately every  
10 seconds  
• The above values are based a new battery, starting from a full charge. Repeated  
charging shortens battery life.  
• Frequency of flash, zoom, and Auto Focus usage, and the time the camera is on  
greatly affects recording time and number of shots values.  
Power Consumption 3.7 V DC, Approximately 3.4 W  
x
x
Dimensions  
98.5 (W) 58.2 (H) 21.2 (D) mm  
x
x
(3.9" (W) 2.3" (H) 0.83" (D))  
Weight  
EX-N1/EX-N2/EX-N20/EX-Z32: Approximately 128g (4.5oz)  
EX-N10: Approximately 132g (4.7oz)  
(including battery and memory card*)  
* 16GB SDHC memory card (SanDisk Corporation)  
EX-N1/EX-N2/EX-N20/EX-Z32: Approximately 111g (3.9oz)  
EX-N10: Approximately 115g (4.1oz)  
(excluding battery and memory card)  
Appendix  
 
126  
 
. Rechargeable lithium ion battery (NP-80)  
Rated Voltage  
3.7 V  
Rated Capacitance  
700 mAh  
Operating Temperature  
Requirements  
0 to 40°C (32 to 104°F)  
x
x
Dimensions  
31.4 (W) 39.5 (H) 5.9 (D) mm  
x
x
(1.24" (W) 1.56" (H) 0.23" (D))  
Weight  
Approximately 15 g (0.53 oz)  
. USB-AC adaptor (AD-C53U)  
Input Power  
100 to 240 V AC, 50/60 Hz, 100 mA  
Output Power  
5.0 V DC, 650 mA  
Operating Temperature  
Requirements  
5 to 35°C (41 to 95°F)  
x
x
Dimensions  
53 (W) 21 (H) 45 (D) mm  
x
x
(2.1" (W) 0.83" (H) 1.8" (D)) (excluding projections)  
Weight  
Approximately 37 g (1.3 oz)  
• Power cord precautions for use in Singapore  
The power cord set is not supplied. The power cord used must comply with  
relevant national and/or international standards.  
Declaration of Conformity According to EU Directive  
Manufacturer:  
CASIO COMPUTER CO., LTD.  
6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan  
Responsible within the European Union:  
CASIO EUROPE GmbH  
Casio-Platz 1, 22848 Norderstedt, Germany  
Appendix  
 
127  
CASIO COMPUTER CO., LTD.  
6-2, Hon-machi 1-chome  
Shibuya-ku, Tokyo 151-8543, Japan  
M29  
MA1207-A  
 
2012  

Black Box Network Card WP170GR User Manual
Black Box Network Hardware dtx5000 ctl r2 User Manual
Black Decker Lawn Mower CM1936Z User Manual
Blomberg Refrigerator KNM1551i User Manual
Bosch Appliances Range HDS7052U User Manual
Bosch Appliances Security Camera EX14 User Manual
Bostitch Air Compressor 175869REVA User Manual
Bradford White Corp Water Heater 705 B User Manual
Carrier Air Conditioner PC 111 User Manual
Channel Plus Switch H838BID User Manual