Chief Manufacturing Indoor Furnishings FSA 1004 User Manual

IN STAL LA TIO N I NST RUCT IONS  
Small Flat Panel Lift Arm  
FSA-1004 and KSA-1004  
The Lift Arm FSA/KSA-1004 is an accessory that can be  
used with a broad range of Small Flat Panel Displays.  
Lift Arm  
The FSA/KSA-1004 allows the user to move a display  
vertically up or down in a 13 inch radius. The lift arm can  
be moved vertically 6-1/2” up from center and 6-1/2”  
down from center.  
The FSA/KSA-1004 is designed to safely hold a display  
weighing up to 25 lbs. (11.3kg). The display can be up to  
30 inches wide.  
The FSA/KSA-1004 accommodates all VESA®  
75mm/100mm compliant displays.  
BEFORE YOU BEGIN  
x
CAUTION: To prevent damage to the mount, which could affect or void the Factory warranty, thoroughly  
study all instructions and illustrations before you begin to install the mount brackets. Pay particular atten-  
tion to the “Important Precautions” on Page 2.  
x
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.  
CHIEF MANUFACTURING INC.  
8832-000041 Rev. F  
©2007 Chief Manufacturing  
03/07  
1-800-582-6480 952-894-6280 FAX 952-894-6918  
8401 EAGLE CREEK PARKWAY, STE. 700  
SAVAGE, MINNESOTA 55378 USA  
 
Installation Instructions  
FSA/KSA-1004  
PARTS  
Tension  
adjustment bolt  
70  
70  
50  
30  
50  
70  
70  
10  
30  
20  
40  
80  
20  
60  
Figure 1. Lift Arm Installation Drawing  
PARTS LIST  
Table 1. Lift Arm Parts  
DESCRIPTION  
PART  
10  
QTY  
LIFT ARM  
1
2
2
1
2
1
4
1
20  
WASHER, UHMW, .640 ID X .845 OD  
WASHER, UHMWPE, .318 ID X .031 OD  
PIVOT PIN, SPF  
30  
40  
50  
CAPSCREW, BUTTON HEAD  
LOCK NUT, NYLOCK  
60  
70  
SPACER, STAINLESS STEEL, .320 X .018  
LARGE LOCK NUT, NYLOCK  
80  
3
 
Installation Instructions  
FSA/KSA-1004  
INSTALLATION  
Adding a lift arm modifies your mount configuration. This  
procedure applies to most small flat panel displays,  
particularly those with a pivot or swing arm, whether wall  
mount or desk mount.  
3. To remove the pivot pin (see Figure 2) from the other  
end, do the following:  
a. If the mount is a pivot/pitch wall mount, remove  
the attaching hardware from the display.  
b. If the mount is wall mounted, desk mounted, or  
has more than one swing arm, remove the  
attaching hardware from the arm closest to the  
display.  
Removing the Display from the Mount  
To remove the display from its mount, perform the  
following steps:  
NOTE: Do not remove the four screws (not shown) that  
NOTE: The two button head cap screws removed from  
the mount will be replaced with longer screws  
when the lift arm is installed.  
attach the display to the interface bracket.  
1. Disconnect the power/audio/video cables from the  
display (not shown).  
NOTE: Keep the pivot pin removed in step 2. This part  
will be used again when the lift arm is installed.  
2. Remove the cap screw, washers, pivot pin, and  
retaining nut from the display end of the mount.  
Refer to Figure 2. Separate the display from the  
mount.  
Cap screw  
Small  
Washer  
Display Mount Parts — Typical  
PART NAME  
SCREW, CAP  
QTY  
2
Pivot Pin  
WASHER, FLAT  
4
SMALL WASHER, NYLON  
LARGE WASHER, NYLON  
NUT, NYLOCK  
2
Flat Washers  
Large  
Washer  
2
2
Nut  
Figure 2. Single Swing Arm (FWS-110) — Example  
4
 
Installation Instructions  
FSA/KSA-1004  
Installing display end of lift arm  
Installing the Lift Arm  
1. Install the original pivot pin (see Figure 3) that was  
retained when the display was removed and a  
washer (20) onto the base of the mount.  
To install the lift arm, perform the following procedures:  
Installing base end of lift arm  
2. Assemble a button head cap screw (50), one  
stainless steel washer (70), washer (30), and a  
second stainless steel washer (70) onto button head  
cap screw (50) as shown in Figure 3.  
1. Locate the tension adjustment bolt on the lift arm  
(see Figure 3). Install the pivot pin (40) and a washer  
(20) onto the base of the mount.  
2. Assemble a button head cap screw (50), one  
stainless steel washer (70), washer (30), and a  
second stainless steel washer (70) onto button head  
cap screw (50) as shown in Figure 3.  
3. Insert the screw assembly (step 2) into the pivot hole  
on the lift arm (10) and the display end of the mount.  
4. Thread the lock nut (80) to the screw assembly (step  
2) at the bottom of the mount.  
3. Insert the screw assembly (step 2) into the pivot hole  
on the lift arm (10) and the base end of the mount.  
CAUTION: Over-tightening a tension screw (50) will  
cause excessive wear and may distort  
adjustment components.  
4. Thread the lock nut (60) to the screw assembly (step  
2) at the bottom of the mount.  
5. Using the 3/16” hex key (provided), tighten the  
button head cap screw (50) into the nut (80) several  
turns, leaving flexibility in the hinged joint. Do not  
over-tighten the cap screw (50).  
CAUTION: Over-tightening a tension screw (50) will  
cause excessive wear and may distort  
adjustment components.  
5. Using the 3/16” hex key (provided), tighten the  
button head cap screw (50) into the nut (60) several  
turns, leaving flexibility in the hinged joint. Do not  
over-tighten the cap screw (50).  
Lift Arm Parts  
ITEM  
10  
20  
30  
40  
50  
60  
70  
80  
PART NAME  
QTY  
1
50  
30  
LIFT ARM  
LARGE WASHER, NYLON  
SMALL WASHER, NYLON  
PIVOT PIN, SPF  
2
2
1
50  
Original  
Pivot  
Pin  
CAP SCREW, BUTTON HEAD  
LOCK NUT, NYLOCK  
2
1
70  
SPACER, STAINLESS STEEL  
LARGE LOCK NUT, NYLOCK  
4
20  
80  
1
40  
10  
20  
60  
Figure 3. Installing Lift Arm  
5
 
Installation Instructions  
FSA/KSA-1004  
Lateral  
Adjusting Lateral Movement  
Tension  
Adjustment  
Bolts  
CAUTION: Over-tightening tension bolt will cause  
excessive wear and may distort adjustment  
components.  
(Typical)  
To adjust the lateral movement tension, perform the  
following procedures:  
1. Slightly tighten or loosen the tension adjustment bolt.  
2. Check for desired tension. Repeat as necessary.  
Adjusting Lift Arm Tension  
CAUTION: Over-tightening tension bolt will cause  
excessive wear and may distort adjustment  
components.  
Adjusting Lateral Movement  
To adjust the tension of the lift arm:  
1. Raise or lower the lift arm until tension adjustment  
bolt appears in the opening.  
Lift Arm Tension  
Adjustment Bolt  
2. Using the 5/32” hex key (provided), adjust the  
tension adjustment bolt, as follows:  
NOTE: There is no fixed number of revolutions to turn  
the tension adjustment bolt. Tighten or loosen  
the bolt, as needed. When the bolt is adjusted  
correctly, the display can be easily raised or  
lowered at any time, and stay in place without  
sagging.  
a. To increase lift arm tension, turn the tension  
adjustment bolt counterclockwise.  
Adjusting Lift Arm Tension  
b. To decrease lift arm tension, turn the tension  
adjustment bolt clockwise.  
3. Raise or lower the lift arm to check for desired  
tension. Repeat step 2 as needed.  
6
 
Installation Instructions  
FSA/KSA-1004  
7
 

Black Box Computer Hardware ACU5050A R2 User Manual
Black Box Server 26589 User Manual
Boca Research Network Card 11Mbps User Manual
Briggs Stratton Lawn Mower Accessory 7105884 User Manual
Bush Hog Brush Cutter 3209 Offset User Manual
Campbell Hausfeld Nail Gun CHN20102 User Manual
Carrier Air Conditioner 38AUZ User Manual
Carrier Dehumidifier P707 User Manual
CFM Fan UVHB26 User Manual
Chicago Electric Saw 91938 User Manual