Chief Manufacturing Indoor Furnishings MCS6000 Series User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Single Ceiling Mount  
MCS6000 Series  
 
Installation Instructions  
MCS6000 Series  
LEGEND  
Tighten Fastener  
Pencil Mark  
Apretar elemento de fijación  
Befestigungsteil festziehen  
Apertar fixador  
Marcar con lápiz  
Stiftmarkierung  
Marcar com lápis  
Segno a matita  
Potloodmerkteken  
Serrare il fissaggio  
Bevestiging vastdraaien  
Serrez les fixations  
Marquage au crayon  
Loosen Fastener  
Drill Hole  
Aflojar elemento de fijación  
Befestigungsteil lösen  
Desapertar fixador  
Perforar  
Bohrloch  
Fazer furo  
Praticare un foro  
Gat boren  
Allentare il fissaggio  
Bevestiging losdraaien  
Desserrez les fixations  
Percez un trou  
Phillips Screwdriver  
Adjust  
Destornillador Phillips  
Ajustar  
Kreuzschlitzschraubendreher  
Chave de fendas Phillips  
Cacciavite a stella  
Einstellen  
Ajustar  
Regolare  
Afstellen  
Ajuster  
Kruiskopschroevendraaier  
Tournevis à pointe cruciforme  
Open-Ended Wrench  
Llave de boca  
Remove  
Quitar  
Gabelschlüssel  
Chave de bocas  
Chiave a punte aperte  
Steeksleutel  
Entfernen  
Remover  
Rimuovere  
Verwijderen  
Retirez  
Clé à fourche  
By Hand  
Optional  
Opcional  
Optional  
Opcional  
Opzionale  
Optie  
A mano  
Von Hand  
Com a mão  
A mano  
Met de hand  
À la main  
En option  
Hex-Head Wrench  
Security Wrench  
Llave de cabeza hexagonal  
Sechskantschlüssel  
Chave de cabeça sextavada  
Chiave esagonale  
Llave de seguridad  
Sicherheitsschlüssel  
Chave de segurança  
Chiave di sicurezza  
Veiligheidssleutel  
Clé de sécurité  
Zeskantsleutel  
Clé à tête hexagonale  
3
 
MCS6000 Series  
Installation Instructions  
TOOLS REQUIRED FOR INSTALLATION  
5/32"  
(Provided)  
PARTS  
A (1)  
B (1)  
5/32"  
4
 
Installation Instructions  
MCS6000 Series  
INSTALLATION  
WARNING: FAILURE TO PROVIDE ADEQUATE  
STRUCTURAL STRENGTH FOR THIS COMPONENT CAN  
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE  
TO EQUIPMENT! It is the installer’s responsibility to make  
sure the structure to which this component is attached can  
support five times the combined weight of all equipment.  
Reinforce the structure as required before installing the  
component.  
1
(A)  
Attaching MCS to NPT Pipe  
CAUTION: Watch for pinch points. Do not place fingers  
between moveable parts.  
Display  
1. Thread the MCS (A) onto the existing 1-1/2" NPT pipe until  
tight. (See Figure 1)  
Figure 2  
2. Using the hex head wrench (B) tighten the set screw into the  
MCS threaded collar to prevent movement of the mount.  
(See Figure 1)  
WARNING: DISPLAY MAY WEIGH IN EXCESS OF 40  
LBS! Always use two people and proper lifting techniques  
when installing or positioning display on MCS.  
NPT  
Pipe  
2. Lower display into place listening for audible "click" to  
ensure recessed area of mounting buttons are properly  
seated in lower area of mounting holes. (See Fig. 2, 3 and 4)  
Set  
Screw  
2
(A)  
(A)  
Interface Bracket  
(will vary in  
appearance)  
of Display  
Back  
Figure 1  
Attaching Interface Bracket to Display  
Figure 3  
1. Attach interface bracket to display following instructions  
included with interface bracket kit.  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
DISPLAY FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Ensure mounting  
buttons are completely engaged in mounting holes.  
Attaching Displays to MCS  
1. While supporting both sides of display, align four mounting  
buttons on display or interface bracket with four mounting  
holes in MCS. (See Figures 2, 3 and 4)  
NOTE: Holes are provided in the faceplate for use with a  
padlock or similar locking device, if desired. In addition,  
the pin and nut may be removed from the upper holes  
and moved to the lower holes for use as a more  
permanent locking device. (See Figure 4).  
5
 
MCS6000 Series  
Installation Instructions  
Remove bolt  
or padlock  
if used  
1
2
May remove  
pin and nut and  
move to lower holes  
4
Pin in  
"Closed"  
position -  
move to  
"Open"  
5
position to  
remove  
display  
A padlock or bolt  
may be placed  
through latch holes  
4
Figure 4  
Removing Display from MCS  
1. Disconnect all power/audio/video cables.  
2. Remove bolt or padlock from faceplate (if used).  
(See Figure 5)  
NOTE: The pin may have been used as a more permanent  
locking device. If so, remove nut and pin and move  
from the lower holes to the upper holes.  
Pin in  
"Open"  
position -  
move to  
"Closed"  
position  
3. Pull back on flag on upper mounting hole and press pin  
down into "Open" position. (See Figure 5)  
after display  
is removed.  
WARNING: THE DISPLAY MAY WEIGH IN EXCESS OF  
40 LBS EACH! Always use two people and proper lifting  
techniques when installing or positioning display on MCS.  
Figure 5  
4. Carefully lift display from MCS.  
5. Lift up on pin and place flag back against faceplate to return  
it to "Closed" position. (See Figure 5)  
Adjusting Display  
CAUTION: Watch for pinch points. Do not place fingers  
between moveable parts.  
Adjusting Roll  
1. Using a 9/16" wrench, loosen the Nylock roll adjustment nut  
on back of mounting plate. (See Figure 6)  
2. Tilt the faceplate left or right as required.  
3. TIghten nut.  
NOTE: Do NOT overtighten fasteners.  
Adjusting Pitch  
1. Adjust display to the desired pitch.  
2. Using the 5/32" hex head wrench (B), tighten the pitch  
adjustment screw to hold mount in position. (See Figure 6)  
6
 
Installation Instructions  
MCS6000 Series  
Roll  
Adjustment  
Nut  
Pitch  
Adjustment  
Screw  
Figure 6  
7
 
MCS6000 Series  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378  
800.582.6480 / 952.894.6280  
877.894.6918 / 952.894.6918  
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands  
+31 (0)40 2668620  
+31 (0)40 2668615  
Asia Pacific  
A
Room 30I, Block D, Lily YinDu International Building  
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112  
8805-000144 Rev. E  
©2007 Chief Manufacturing  
10/07  
P
F
+86-755-8996 9226 ; 8996 9236 ; 8996 9220  
+86-755-8996 9217  
 

Belkin Network Card 8820 01363 User Manual
Belkin Network Router PM00781EA F5D8635 4 User Manual
Blanco Indoor Furnishings 441020 User Manual
Bogen Speaker System 1092151 User Manual
Bolens Lawn Mower 120 255A User Manual
Bolens Trimmer 245 604 000 User Manual
Bowers Wilkins Speaker DM14 User Manual
Briggs Stratton Portable Generator 30342 User Manual
Bushnell Binoculars Model 26 0542 User Manual
Carrier Heat Pump 50PQ User Manual